Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Rearview Camera Image Does Not Change When Selecting Different Views (2015-18)
NOTE:
- Check the vehicle 12 volt battery condition first - Refer to: 12 Volt Battery Test (Without SH-AWD) or 12 Volt Battery Test (With SH-AWD) .
- You can select three different rearview camera angles for backing up. If there is no camera image on the display, refer to: Rearview Camera Image Does Not Come On (2015-18) .
- Check the connectors for poor connections or loose terminals.
- Problem verification
- 1. Turn the vehicle to the ON mode, then shift the transmission to R position/mode.
If needed, start the engine, then apply the parking brake, and shift the transmission to R position.
- 2. Press the ENTER button to see if the rearview image changes between the wide view, the normal view, and the top down view in this order.
Does the rearview camera image change properly?
YES
Intermittent failure, the system is OK at this time.
NO
The failure is duplicated, go to step 2.
- Shorted wire check (CAMERA BIT0 line, CAMERA BIT1 line)
- 1. Shift the transmission to P position/mode.
- 2. Turn the vehicle to the OFF (LOCK) mode.
- 3. Disconnect the following connectors.
Audio-navigation unit connector G (24P) Rearview camera 12P connector - 4. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Audio-navigation unit connector G (24P): disconnected Rearview camera 12P connector: disconnected Test point 1 Audio-navigation unit connector G (24P) No. 5 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Body ground Test point 1 Audio-navigation unit connector G (24P) No. 18 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Body ground Is there continuity?
YES
Repair a short to body ground in the wire (s) between the rearview camera and the audio-navigation unit.
NO
The CAMERA BIT0 and the CAMERA BIT1 wires are not shorted to ground. Go to step 3.
- Shorted wire check (CAMERA BIT0 line to CAMERA BIT1 line)
- 1. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Audio-navigation unit connector G (24P): disconnected Rearview camera 12P connector: disconnected Test point 1 Audio-navigation unit connector G (24P) No. 5 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Audio-navigation unit connector G (24P) No. 18 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Is there continuity?
YES
Repair a short in the wires between the rearview camera and the audio-navigation unit.
NO
The CAMERA BIT0 and the CAMERA BIT1 wires are not shorted. Go to step 4.
- Open wire check (CAMERA BIT0 line, CAMERA BIT1 line)
- 1. Check for continuity between test points 1 and 2.
Test condition Vehicle OFF (LOCK) mode Audio-navigation unit connector G (24P): disconnected Rearview camera 12P connector: disconnected Test point 1 Audio-navigation unit connector G (24P) No. 5 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Rearview camera 12P connector No. 5 - Refer to: Rearview Camera Connector For Inputs And Outputs (2015-17) or Rearview Camera Connector for Inputs and Outputs (2018-19) Test point 1 Audio-navigation unit connector G (24P) No. 18 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Rearview camera 12P connector No. 6 - Refer to: Rearview Camera Connector For Inputs And Outputs (2015-17) or Rearview Camera Connector for Inputs and Outputs (2018-19) Is there continuity?
YES
The CAMERA BIT0 and the CAMERA BIT1 wires are OK. Go to step 5.
NO
Repair an open in the wire (s) between the rearview camera and the audio-navigation unit.
- Voltage check (CAMERA BIT0 line)
- 1. Reconnect audio-navigation unit connector G (24P).
- 2. Reconnect the rearview camera 12P connector.
- 3. Turn the vehicle to the ON mode.
- 4. Go into the System Diagnostic Mode, and use the Guideline Setup to display each view mode.
- 5. Measure the voltage between test points 1 and 2 as specified in the table.
Test condition Vehicle ON mode Test point 1 Audio-navigation unit connector G (24P) No. 5 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Body ground Selected view mode Voltage Wide View 0 V Normal View About 8 V Top Down View 0 V Is the voltage OK?
YES
Go to step 6.
NO
- Voltage check (CAMERA BIT1 line)
- 1. Measure the voltage between test points 1 and 2 as specified in the table.
Test condition Vehicle ON mode Test point 1 Audio-navigation unit connector G (24P) No. 18 - Refer to: Audio-Navigation Unit Connector For Inputs And Outputs (With Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Without Auto Idle Stop System) (2015-17) or Audio-Navigation Unit Connector for Inputs and Outputs (Undefined) (2018), or Audio-Navigation Unit Connector for Inputs and Outputs (2019) Test point 2 Body ground Selected view mode Voltage Wide View 0 V Normal View 0 V Top Down View About 8 V Is the voltage OK?
YES
NO
NO RELATED
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.