2013 ILX And ILX Hybrid: TQI And New Model Service Information (12-019)

Working With a Flat Lift

A flat lift may interfere with the underside of the vehicle. Use attachments that eliminate the chance of damage to the underside of the vehicle.

Install the Fuses

To prevent battery drain during shipment, the No. 29 Backup fuse (10 A) and the No. 28 Interior Light fuse (7.5 A) are removed from the under-hood fuse/relay box and stored in the glove box. Make sure you install these fuses in the proper sockets with the ignition OFF.

Check the Battery

To ensure a long life for the battery and that the client receives one that is fully charged, the battery must be checked at these times:

• When the vehicle first arrives at the dealership
• During TQI, if done at a later date
• At regular intervals, if stored
• Just before delivering a vehicle to a client

Test the battery with the ED-18 battery tester using the instructions in Service Bulletin 88-016, Battery Testing and Replacement.  If the ED-18 tester results display GR8 DIAGNOSTIC NEEDED  , you must properly charge the battery using the GR8 Battery Diagnostic Station.

Write down the GOOD BATTERY  10-digit code in the maintenance journal. During the PDI, write down the code in the "Under Hood (Engine Cold)" section, and then, when the vehicle is delivered to the client, write down the code in the "Final Inspection (At Delivery)" section.

Install the Shift Lock Release Cover (A/T and CVT Models)

The shift lock release cover is in a plastic bag with the owner's manual in the glove box. Install the cover in the shift lock release opening to the right of the shift lever.

Set the Radio Anti-Theft Code

The anti-theft code is automatically checked between the PCM and the audio unit; there is no longer a need for anti-theft code cards. However, two anti-theft code labels are included. After you exit the anti-theft mode, attach one of the anti-theft code labels to the TQI repair order. The second label should be given to the client for safe keeping, rather than left in the vehicle. in order to exit the anti-theft mode, do this:

1. Start the engine.
2. Wait for the following message to appear on the display.
3. Press the audio unit power button to turn on the audio unit. When ENTER CODE appears on the audio unit display, press and hold the audio unit power button for about 2 seconds to allow the PCM to verify the vehicle's VIN and the VIN saved in the audio unit match. You will hear a long beep when the audio unit exits the anti-theft mode. Release the power button.

Check/Refresh the XM Satellite Radio Dealer Demo Service (All Except Alaskan and Hawaiian Models)

The audio system comes from the factory activated with the XM Satellite Radio dealer demo service. The XM radio receives the full range of available XM channels. Make sure this service is activated by tuning to several XM channels. You can see the full list of XM channels at www.xmradio.com.  If the XM radio receives only a small number of channels such as 000  , 001  , and 247  , the dealer demo is not activated.

To check for the dealer demo service, do this:

1. Turn the ignition switch to ON (II).
2. Turn on the radio, enter the 5-digit navigation anti-theft code (if not already done), and press the XM button.
3. Make sure the radio is in CHANNEL MODE  , not CATEGORY MODE  . Press the SETUP  button, select "XM Mode"  , and then select CHANNEL MODE  (without navigation), or go to the Audio menu and select CH  (with navigation) to switch between modes.
4. Tune to channel 001  (the XM preview channel) to make sure you are receiving the XM signal. If you do not get a clear signal, park the vehicle outside where there is a clear view of the southern sky.
5. While watching the audio unit display, tune to several channels within the full XM lineup. To see the full list of channels, go to www.xmradio.com. 
   • If you can tune to all of the XM channels, the dealer demo service is activated. Tune to channel 001  , and leave the radio on for 7 minutes to refresh the dealer demo service. No further action is needed.
   • If you can only tune to a few channels like 000  , 001  , and 247  , the dealer demo service is not yet activated, and an activation refresh needs to be done. Go to step 6.
6. Turn to 000  , then write down the 8-digit XM radio ID you see in the audio unit display. You need this ID, your dealer number, and the VIN to do an activation refresh of the dealer demo service. Go to step 7.
   NOTE:

   • If you cannot tune to channel 000  , you are in CATEGORY MODE  . See step  3 above to switch from CATEGORY MODE  to CHANNEL MODE. 
   • Check the ID code carefully. The letters I, O, S, and F are not used.
7. Go to an iN workstation.
   NOTE: If you do not have access to the iN, call XM Satellite Radio at 800-852-9696  , and follow the instructions of the automated menu. When the agent answers, ask for a rapid dealer activation refresh, then go to step  10.
8. From the iN main menu, click on SERVICE  , click on Service Bay  , and then click on XM Radio.  This brings up the DEALER ACTIVATION REFRESH  screen.
   NOTE: If you cannot bring up this display, call the iN Support Center at 800-245-4343. 
9. Enter the 8-digit XM radio ID you wrote down in step  6. Then click on Submit.  You will see the ACTIVATION REFRESH  screen once the ID is recognized.
   NOTE: If you entered the ID incorrectly, or it was not recognized, you will see an error display. If this happens, follow the instructions on the display.
10. Turn to 001  to make sure you are receiving the XM signal. If you do not get a clear signal, park the vehicle outside where there is a clear view of the southern sky, then go to step 11.
11. Leave the radio on for at least 10 minutes, then go to step 12.
12. While watching the audio unit display, tune to several stations within the full XM lineup.
    • If you can tune to all the XM channels, the dealer demo service is activated, and no further action is needed.
    • If you can only tune to a few channels like 000  , 001  , and 247  , repeat steps  7 thru 12.
    • If, after two hours, you can only tune to channels 000  , 001  , and 247  , call XM Satellite Radio at 800-852-9696.  When you hear the automated menu, enter priority code 9466  to route your call to an XM agent. When the agent answers, ask them to review the account status and make any necessary corrections. If the account status is correct for the vehicle, replace the XM receiver.
      NOTE:

      • The dealer demo service lasts for 7 months or until the vehicle's RDR (retail delivery registration) is submitted.
      • After the vehicle is registered, the dealer demo service converts to a client account. The client gets a 3-month trial service of all available non-premium XM channels. If the client decides to end the service after that time, the XM radio reverts to preview mode. Normal AM and FM radio reception is not affected by ending the service.
      • The XM radio receives digital programming broadcasts from two fixed-orbit satellites above the equator along with a network of ground antennas (repeaters). You will get the strongest signal if you park the vehicle where there is a clear view of the southern sky.
      • The XM radio may lose reception when you are driving through a tunnel, under an overpass, inside a parking garage, in a canyon, or near the northern face of a canyon or a mountain.
      • To cut down on reception loss, the XM radio uses a buffer. If the reception loss lasts longer than the buffering period, the signal goes silent.
      • Because the XM radio signal is digital, any reception loss makes the signal go silent; the signal usually does not fade like it does with a conventional radio.
      • If you ever need to replace the XM radio receiver, call XM Satellite Radio at 800-852-9696.  Be prepared to give them your dealer number, the VIN, and the XM radio ID from the printed label on the side of the old and the new receiver units.
      • Your client's XM radio presets will be lost if you disconnect the battery or if it goes dead. Always write down the XM radio presets before you disconnect the battery.

Check the HandsFreeLink System

To confirm that the HFL (HandsFreeLink) system is working and ready to use, start the engine and hold the HANG UP  button for 2 seconds, you should hear the HFL message: "The HFT is OK." If you do not hear the HFL message, refer to the online service manual for troubleshooting information.

Setting the Clock (Without Navigation)

1. Push the AUX or SETUP button to display the setup screen.
2. Select "adjust clock" using the TUNE SELECT button.
3. Use the TUNE SELECT button to set the time. When you are done select SET.

Do the Idle Learn Procedure

To ensure a steady engine idle, do the idle learn procedure after installing the No. 29 fuse.

1. Make sure all electrical items (A/C, radio, rear window defogger, lights, etc.) are off.
2. Start the engine, and let it reach operating temperature (the cooling fans cycle twice).
3. Let the engine idle for 10 minutes with the throttle closed.

The idle learn procedure must also be done after updating or replacing the PCM. It does not need to be done after you clear DTCs.

Remove the Interior Protective Coatings

There are several protective coverings on the interior trim pieces and some areas of carpet. Carefully remove all of them. Remove the coverings with clean hands so you don't soil the fabric. If any of the interior is dirty, clean it with mild soap or an Acura cleaning product such as Leather and Vinyl Cleaner (P/N 08700-9214A) or Carpet Spot Remover (P/N 08700-9215A).

Install the Floor Mats (If Applicable)

The floor mats are in the trunk. Install them in the appropriate positions. Place the driver's and the front passenger's floor mat eyelets over the anchors on the floor, then turn the knobs clockwise to lock the anchors. Place the rear floor mat eyelet over the anchors on the floor, then turn the knobs clockwise to lock the anchors.

Remove the Protective Tape From the Front Strakes

Protective tape is attached to the front strakes to avoid damage during transportation.

Install the Body Plugs

Four body plugs are in the glove box. Install the plugs into the tie-down holes in front of the rear wheels and near the front of the vehicle.

Install the Front License Plate Holder

For shipping purposes, the license plate holder is stored in the trunk. If state regulations require the use of a front license plate, install the front license plate holder as shown:

Do the Auto Idle Stop Test (Hybrid)

To improve overall fuel economy, the auto idle stop feature shuts off the engine when the vehicle comes to a stop.

1. Make sure the IMA battery charge display shows that the battery is more than 50 percent charged.
2. Make sure that the engine is at normal operating temperature.
3. Turn off the climate controls and the defroster.
4. Test-drive the vehicle above 30 mph for at least 3 minutes.
5. Come to a normal stop, and do not release the brake pedal. The engine should stop.
6. Make sure the engine stops and the auto idle stop indicator in the gauge control module flashes.
7. Release the brake pedal, and accelerate normally.
   NOTE:

   • The engine should automatically restart when you release the brake pedal.
   • If the vehicle is going into storage after charging, remove the two fuses installed earlier to prevent drain on the 12V battery.

Charge the IMA System Battery (Hybrid)

1. Start the engine.
2. Hold the engine at 4,000 rpm, and watch the IMA charge display.
3. Continue to hold the engine rpm between 3,500 and 4,000 until the hybrid battery stops charging.
   NOTE: The IMA battery will not fully charge until the vehicle is driven.

Long-Term IMA Battery Storage (Hybrid)

If the vehicle has been stored for 1 year or more since it was purchased, charge the IMA battery as described above.

How to Set the Hood Vertically

1. You can prop the hood close to 90 degrees. Move the hood support rod from the front bulkhead to the hole in the side bulkhead.
2. Remove the grommet from the hood insertion opening, and insert the support rod.

New Stamped VIN Location

Unlike previous models, the VIN is no longer on the engine compartment bulkhead; it's on the floor panel in front of the front passenger's seat.

Tire Repair Kit (Hybrid)

The ILX Hybrid does not have a spare tire. Make sure the tire repair kit is in place beneath the trunk floor.

One Motion Door Unlock

The Acura ILX is equipped with a feature that opens a locked driver's or front passenger's door by a single operation of the inside handle.

Expanded View Driver's Mirror

The driver's mirror has outer and inner segments. The outer segment is slightly curved to provide a wider angle of view of what's on the left side of the vehicle. If a client complains of distortion, the first step is to tape off the outer segment of the mirror, then inspect the remainder of the mirror for distortion.

One-Push Turn Signal

When you lightly push the turn signal lever for a lane change, the turn signals flashes three times, then go off.

Headlight Integration With Windshield Wiper

This system turns the headlights on when the windshield wipers are activated and when the headlight switch is in the Auto mode.

Opening the Center Console

To open the center console lid, push the button as shown.

Windshield Washer Nozzle Aiming

In order to adjust the aim of the windshield washer nozzle, insert two straight pins into the two openings above and below the spray opening. Adjust up and down as shown. Do not insert anything into the spray opening.