Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Acura RLFACTORY OEM SERVICE PROCEDURE
Automatic Transmission DTCS
AUTOMATIC TRANSMISSION DIAGNOSTIC TROUBLE CODE (DTC) DENTIFICATION
| DTC | Detection Item |
|---|---|
| P0705 | Transmission Range Switch (Multiple Shift-position Input) |
| P0706 | Transmission Range Switch (Open) |
| P0711 | ATF Temperature Sensor (Range/Performance) |
| P0712 | ATF Temperature Sensor (Short) |
| P0713 | ATF Temperature Sensor (Open) |
| P0716 | Input Shaft (Mainshaft) Speed Sensor (Range/Performance) |
| P0717 | Input Shaft (Mainshaft) Speed Sensor (No Signal Input) |
| P0718 | Input Shaft (Mainshaft) Speed Sensor (Intermittent Failure) |
| P0721 | Output Shaft (Countershaft) Speed Sensor (Range/Performance) |
| P0722 | Output Shaft (Countershaft) Speed Sensor (No Signal Input) |
| P0723 | Output Shaft (Countershaft) Speed Sensor (Intermittent Failure) |
| P0731 | 1st Gear Incorrect Ratio |
| P0732 | 2nd Gear Incorrect Ratio |
| P0733 | 3rd Gear Incorrect Ratio |
| P0734 | 4th Gear Incorrect Ratio |
| P0735 | 5th Gear Incorrect Ratio |
| P0741 | Torque Converter Clutch Circuit Performance or Stuck OFF |
| P0746 | A/T Clutch Pressure Control Solenoid Valve A Stuck OFF |
| P0747 | A/T Clutch Pressure Control Solenoid Valve A Stuck ON |
| P0751 | Shift Solenoid Valve A Stuck OFF |
| P0752 | Shift Solenoid Valve A Stuck ON |
| P0756 | Shift Solenoid Valve B Stuck OFF |
| P0757 | Shift Solenoid Valve B Stuck ON |
| P0761 | Shift Solenoid Valve C Stuck OFF |
| P0762 | Shift Solenoid Valve C Stuck ON |
| P0766 | Shift Solenoid Valve D Stuck OFF |
| P0767 | Shift Solenoid Valve D Stuck ON |
| P0776 | A/T Clutch Pressure Control Solenoid Valve B Stuck OFF |
| P0777 | A/T Clutch Pressure Control Solenoid Valve B Stuck ON |
| P0796 | A/T Clutch Pressure Control Solenoid Valve C Stuck OFF |
| P0797 | A/T Clutch Pressure Control Solenoid Valve C Stuck ON |
| P0812 | Transmission Range Switch ATP R Switch (Open) |
| P0842 | 2nd Clutch Transmission Fluid Pressure Switch (Short or Stuck ON) |
| P0843 | 2nd Clutch Transmission Fluid Pressure Switch (Open or Stuck OFF) |
| P0847 | 3rd Clutch Transmission Fluid Pressure Switch (Short or Stuck ON) |
| P0848 | 3rd Clutch Transmission Fluid Pressure Switch (Open or Stuck OFF) |
| P0872 | 4th Clutch Transmission Fluid Pressure Switch (Short or Stuck ON) |
| P0873 | 4th Clutch Transmission Fluid Pressure Switch (Open or Stuck OFF) |
| P0962 | A/T Clutch Pressure Control Solenoid Valve A (Short) |
| P0963 | A/T Clutch Pressure Control Solenoid Valve A (Open) |
| P0966 | A/T Clutch Pressure Control Solenoid Valve B (Short) |
| P0967 | A/T Clutch Pressure Control Solenoid Valve B (Open) |
| P0970 | A/T Clutch Pressure Control Solenoid Valve C (Short) |
| P0971 | A/T Clutch Pressure Control Solenoid Valve C (Open) |
| P0973 | Shift Solenoid Valve A (Short) |
| P0974 | Shift Solenoid Valve A (Open) |
| P0976 | Shift Solenoid Valve B (Short) |
| P0977 | Shift Solenoid Valve B (Open) |
| P0979 | Shift Solenoid Valve C (Short) |
| P0980 | Shift Solenoid Valve C (Open) |
| P0982 | Shift Solenoid Valve D (Short) |
| P0983 | Shift Solenoid Valve D (Open) |
| P1717 | Transmission Range Switch ATP RVS Switch (Open) |
| P1743 | Shift Error |
| P1744 | Shift Error |
| P1745 | Shift Error |
| P1780 | Shift Control System (Transmission Default Mode) |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
