Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA2008TL V6-3.5LREPAIR AND DIAGNOSISPOWERTRAIN MANAGEMENTIGNITION SYSTEMIGNITION TIMINGTESTING AND INSPECTION
2008 Acura TL V6-3.5L
Ignition Timing: Testing and Inspection
2008 Acura TL V6-3.5LSECTION Testing and Inspection
Ignition Timing Inspection
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC).
2. Turn the ignition switch ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain control module (PCM). If it doesn't communicate, troubleshoot the DLC circuit.
4. Check for DTCs. If a DTC is present, diagnose and repair the cause before inspecting the ignition timing.
5. Start the engine. Hold the engine speed at 3,000 rpm with no load (in the N or P position (A/T) or neutral (M/T)) until the radiator fan comes on, then let it idle.
6. Check the idle speed.
7. Jump the SCS line with the HDS.
8. Remove the right side engine compartment cover.
9. Connect the timing light to the No. 1 ignition coil harness.
10. Aim the light toward the pointer (A) on the timing belt cover. Check the ignition timing under a no load condition, (headlights, blower fan, rear window defogger, and air conditioner are turned off).
11. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK, update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the system works properly, and the ECM/PCM was substituted, replace the original ECM/PCM.
12. Disconnect the HDS and the timing light.
13. Reinstall the right side engine compartment cover.
1. Connect the Honda Diagnostic System (HDS) to the data link connector (DLC).
2. Turn the ignition switch ON (II).
3. Make sure the HDS communicates with the vehicle and the engine control module (ECM)/powertrain control module (PCM). If it doesn't communicate, troubleshoot the DLC circuit.
4. Check for DTCs. If a DTC is present, diagnose and repair the cause before inspecting the ignition timing.
5. Start the engine. Hold the engine speed at 3,000 rpm with no load (in the N or P position (A/T) or neutral (M/T)) until the radiator fan comes on, then let it idle.
6. Check the idle speed.
7. Jump the SCS line with the HDS.
8. Remove the right side engine compartment cover.
9. Connect the timing light to the No. 1 ignition coil harness.
10. Aim the light toward the pointer (A) on the timing belt cover. Check the ignition timing under a no load condition, (headlights, blower fan, rear window defogger, and air conditioner are turned off).
11. If the ignition timing differs from the specification, check the cam timing. If the cam timing is OK, update the ECM/PCM if it does not have the latest software, or substitute a known-good ECM/PCM, then recheck. If the system works properly, and the ECM/PCM was substituted, replace the original ECM/PCM.
12. Disconnect the HDS and the timing light.
13. Reinstall the right side engine compartment cover.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.