Safety Warning

DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.

SYS.OK|MANUAL.DB● LIVE

HOMESERVICE MANUALSACURA20043.5RLREPAIR AND DIAGNOSIS (SINGLE PAGE)EXTERNAL PAGESDIFFERENT CARSECTION 6 (SPECIFICATIONS & PROCEDURES)WHEEL ALIGNMENT SPECIFICATIONS

2004 Acura 3.5RL

Wheel Alignment Specifications

2004 Acura 3.5RLSECTION Wheel Alignment Specifications

WARNING: This page is about a different car, the 2001 Acura MDX, 2001 Acura Integra, 2001 Acura 3.5RL, 2001 Acura 3.2TL, and 2001 Acura 3.2CL. However, it is still accessible from the selected car via links, so may be relevant.

WHEEL ALIGNMENT SPECIFICATIONS

Application

Preferred

Range

Integra (Except Type-R)

Camber ⁽¹⁾

Front

- .17

- 1.17 To .83

Rear

- .75

- 2.0 To 0

Caster ⁽¹⁾

Front

1.17

.17 To 2.17

Toe-In ⁽¹⁾

Front

- .16 To .16

Rear

.16

.08 To .32

Toe-In ⁽²⁾

Front

0 (0)

- .08 To .08 (- 2 To 2)

Rear

.08 (2)

.04 To .16 (1 To 4)

Toe-Out On Turns ⁽¹⁾

Inner

34 To 38

Outer

30.5

N/A

Integra Type-R

Camber ⁽¹⁾

Front

- .5

- 1.5 To 1

Rear

- .75

- 2.0 To 0

Caster ⁽¹⁾

Front

1.17

.17 To 2.17

Toe-In ⁽¹⁾

Front

- .16 To .16

Rear

.16

.08 To .32

Toe-In ⁽²⁾

Front

0 (0)

- .08 To .08 (- 2 To 2)

Rear

.08 (2)

.04 To .16 (1 To 4)

Toe-Out On Turns ⁽¹⁾

Inner

34 To 38

Outer

30.5

N/A

MDX

Camber ⁽¹⁾

Front

- .30

-1.30 To .30

Rear

-.30

-1.05 To .45

Caster ⁽¹⁾

Front

1.53

.53 To 2.53

Toe-In ⁽¹⁾

Front

- .16 To .16

Rear

- .16 To .16

Toe-In ⁽²⁾

Front

0 (0)

- .08 To .08 (- 2 To 2)

Rear

0 (0)

- .08 To .08 (- 2 To 2)

Toe-Out On Turns ⁽¹⁾

Inner

38.08

N/A

Outer

30.19

N/A

3.2CL

Camber ⁽¹⁾

Front

-1 To 1

Rear

- .50

- 1.5 To .50

Caster ⁽¹⁾

Front

2.8

1.8 To 3.8

Toe-In ⁽¹⁾

Front

- .16 To .16

Rear

.16

0 To .16

Toe-In ⁽²⁾

Front

0 (0)

- .08 To .08 (- 2 To 2)

Rear

.08 (2)

0 To .16 (0 To 4)

Toe-Out On Turns ⁽¹⁾

Except Type S

Inner

38.5

Outer

31.0

N/A

Type S

Inner

35.3

Outer

29.2

N/A

3.2TL

Camber ⁽¹⁾

Front

- 1 To 1

Rear

- .5

- 1.5 To .5

Caster ⁽¹⁾

Front

2.8

1.8 To 3.8

Toe-In ⁽¹⁾

Front

- .08

- .24 To .08

Rear

.24

.08 To .40

Toe-In ⁽²⁾

Front

-.08 To .08 (-2 To 2)

Rear

.08 (2)

0 To .16 (0 To 4)

Toe-Out On Turns ⁽¹⁾

Inner

38.60

36.6 To 40.6

Outer

31.05

N/A

3.5RL

Camber ⁽¹⁾

Front

- 1 To 1

Rear

- .5

- 1.5 To .5

Caster ⁽¹⁾

Front

2.83

1.83 To 3.83

Toe-In ⁽¹⁾

Front

- .16 To .16

Rear

.16

0 To .32

Toe-In ⁽²⁾

Front

0 (0)

- .08 To .08 (- 2 To 2)

Rear

.08 (2)

0 To .16 (0 To 4)

Toe-Out On Turns ⁽¹⁾

Inner

41.5

39.5 To 43.5

Outer

33.9

N/A

⁽¹⁾	Measurements are in degrees.

⁽²⁾	Measurements are in inches (mm).

RENDER: 1.0x

NO RELATED

Recommended Tools & Savings

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Affiliate disclosure: We may earn a commission at no extra cost to you.

Shop Manual-Ready Tools Free Quote Check Quote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

• You smell fuel, burning insulation, or see smoke.
• Brakes feel soft, pull hard to one side, or make grinding noises.
• The engine overheats, stalls repeatedly, or misfires under load.
• You are missing required tools, torque specs, or safe lifting equipment.
• You are not confident in the next step or safety outcome.