Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA1998CL V6-3.0L SOHC (VTEC)REPAIR AND DIAGNOSISTECHNICAL SERVICE BULLETINSALL TECHNICAL SERVICE BULLETINSKEYLESS ENTRY - DESCRIPTION/IDENTIFICATION/PROGRAMMINGWITH DEALER-INSTALLED SECURITY SYSTEM AND KEYLESS ENTRY SYSTEM1994-96 INTEGRA
1998 Acura CL V6-3.0L SOHC (VTEC)
1994-96 Integra
1998 Acura CL V6-3.0L SOHC (VTEC)SECTION 1994-96 Integra
1994-96 Integra with dealer-installed security system
Programming the Transmitter
NOTES:
^ The system uses a stacking-type memory that accepts up to four transmitters. If you program a fifth transmitter, the system's memory for the first transmitter is pushed out, and it will no longer work.
^ To clear a lost or stolen transmitter from the system's memory, erase all transmitter codes and then reprogram them. Refer to the security system owner's manual.
^ If the valet/disarm button is released before programming is complete, the system will exit the programming mode.
1. Turn the ignition switch to ON (II).
2. Press and hold the Valet-Disarm button on the dashboard lower cover. (Continue to hold the button during this procedure, or programming will be cancelled.) The LED on the upper steering column cover flashes when the system is in programming mode.
3. Press the top button on the transmitter. Check that the parking lights flash to confirm that the transmitter's code was accepted.
4. Press the top button on each of the remaining transmitters. Check that the parking lights flash after each transmitter code is accepted.
5. Release the Valet-Disarm button to exit the programming mode.
Ordering a Transmitter
Transmitters can be ordered only by authorized Acura dealers. Order them from American Honda using normal parts ordering procedures.
Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.
Programming the Transmitter
NOTES:
^ The system uses a stacking-type memory that accepts up to four transmitters. If you program a fifth transmitter, the system's memory for the first transmitter is pushed out, and it will no longer work.
^ To clear a lost or stolen transmitter from the system's memory, erase all transmitter codes and then reprogram them. Refer to the security system owner's manual.
^ If the valet/disarm button is released before programming is complete, the system will exit the programming mode.
1. Turn the ignition switch to ON (II).
2. Press and hold the Valet-Disarm button on the dashboard lower cover. (Continue to hold the button during this procedure, or programming will be cancelled.) The LED on the upper steering column cover flashes when the system is in programming mode.
3. Press the top button on the transmitter. Check that the parking lights flash to confirm that the transmitter's code was accepted.
4. Press the top button on each of the remaining transmitters. Check that the parking lights flash after each transmitter code is accepted.
5. Release the Valet-Disarm button to exit the programming mode.
Ordering a Transmitter
Transmitters can be ordered only by authorized Acura dealers. Order them from American Honda using normal parts ordering procedures.
Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.