Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSACURA1994INTEGRA (GS-R) L4-1797CC 1.8L DOHC (VTEC)REPAIR AND DIAGNOSISBODY AND FRAMELOCKSTECHNICAL SERVICE BULLETINSALL TECHNICAL SERVICE BULLETINSKEYLESS ENTRY - DESCRIPTION/IDENTIFICATION/PROGRAMMINGWITH FACTORY-INSTALLED SECURITY SYSTEM1996-01 3.5RL
1994 Acura Integra (GS-R) L4-1797cc 1.8L DOHC (VTEC)
1996-01 3.5RL
1994 Acura Integra (GS-R) L4-1797cc 1.8L DOHC (VTEC)SECTION 1996-01 3.5RL
1996-01 3.5RL with factory-installed security system
Programming the Transmitter
NOTES:
^ The system accepts up to three transmitters.
^ Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode.
^ You must perform each of the first 12 steps within 5 seconds of each other to enter programming mode. Programming each transmitter (step 13) must be done within 10 seconds.
1. Make sure the doors are unlocked.
2. Turn the ignition switch to ON (II).
3. Press the "LOCK" or "UNLOCK" button on the transmitter.
4. Turn the ignition switch to ACCESSORY (I) or LOCK (0).
5. Turn the ignition switch to ON (II).
6. Press the "LOCK" or "UNLOCK" button on the same transmitter.
7. Turn the ignition switch to ACCESSORY (I) or LOCK (0).
8. Turn the ignition switch to ON (II).
9. Press the "LOCK" or "UNLOCK" button on the same transmitter.
10. Turn the ignition switch to ACCESSORY (I) or LOCK (0).
11. Turn the ignition switch to ON (II).
12. Press the "LOCK" or "UNLOCK" button on the same transmitter. Make sure the door locks cycle to indicate that the system has entered programming mode.
13. Press the "LOCK" button on each transmitter that is being programmed. Make sure the power door locks cycle each time to indicate the transmitter has been accepted.
14. Turn the ignition switch to LOCK (0) to exit the programming mode.
Turning the Audible Chirp On/Off
To turn the audible chirp on, press and hold the "TRUNK RELEASE' button, then immediately press and hold the "LOCK" button. The LED on the transmitter will come on for one second. Release the buttons when the LED goes out. Repeat this procedure to turn the audible chirp off. The LED will blink twice.
Ordering a Transmitter
Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures.
Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.
Programming the Transmitter
NOTES:
^ The system accepts up to three transmitters.
^ Entering the programming mode cancels all learned transmitter codes, so none of the previously programmed transmitters will work. You must reprogram all of the transmitters once you are in the programming mode.
^ You must perform each of the first 12 steps within 5 seconds of each other to enter programming mode. Programming each transmitter (step 13) must be done within 10 seconds.
1. Make sure the doors are unlocked.
2. Turn the ignition switch to ON (II).
3. Press the "LOCK" or "UNLOCK" button on the transmitter.
4. Turn the ignition switch to ACCESSORY (I) or LOCK (0).
5. Turn the ignition switch to ON (II).
6. Press the "LOCK" or "UNLOCK" button on the same transmitter.
7. Turn the ignition switch to ACCESSORY (I) or LOCK (0).
8. Turn the ignition switch to ON (II).
9. Press the "LOCK" or "UNLOCK" button on the same transmitter.
10. Turn the ignition switch to ACCESSORY (I) or LOCK (0).
11. Turn the ignition switch to ON (II).
12. Press the "LOCK" or "UNLOCK" button on the same transmitter. Make sure the door locks cycle to indicate that the system has entered programming mode.
13. Press the "LOCK" button on each transmitter that is being programmed. Make sure the power door locks cycle each time to indicate the transmitter has been accepted.
14. Turn the ignition switch to LOCK (0) to exit the programming mode.
Turning the Audible Chirp On/Off
To turn the audible chirp on, press and hold the "TRUNK RELEASE' button, then immediately press and hold the "LOCK" button. The LED on the transmitter will come on for one second. Release the buttons when the LED goes out. Repeat this procedure to turn the audible chirp off. The LED will blink twice.
Ordering a Transmitter
Transmitters can be ordered only by authorized Honda dealers. Order them from American Honda using normal parts ordering procedures.
Batteries for the Transmitter
The battery number is CR2025. Each transmitter uses one battery.
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.