Wiring Diagram Cluster

1998 Nissan-Datsun Altima GXE Starter Wiring Diagram

Find starter circuit schematics, relay paths, and ignition-switch to solenoid wiring references for this vehicle.

Matched Diagrams

48

Variant Used

Altima GXE L4-2.4L (KA24DE)

Total Vehicle Diagrams

1840

πŸ€– Stuck on this electrical issue?

Wiring diagrams can be a maze. Ask Manuel, our factory-trained AI mechanic, to analyze this circuit or troubleshoot your specific symptom.

Ask AI Mechanic βž”

From Diagram To Fix

Use this wiring page as the jump point, not the dead end

Open the exact diagram, then move directly into the vehicle hub, the repair most likely tied to this system, or the code cluster that usually shows up with it.

Keep context

Vehicle Repair Hub

Step out of raw diagrams and into the full 1998 Nissan-Datsun Altima GXE hub with repairs, specs, codes, and other systems already tied to this car.

View vehicle repair hub β†’

OEM source

Factory Manual Evidence

When there is no clean repair shortcut for this system, drop into the OEM manual sections that usually carry the authoritative test path.

Open interactive browser β†’

Diagnostic signal

Codes Often Seen With This System

Use the code cluster when wiring faults overlap with check-engine or module-level diagnostics.

B1318: Battery Voltage Low β†’

Top Starter Diagram Paths

1.Power and Ground Distribution β€” Connector Views > Battery Power Supply - Ignition Switch In Any PositionStarting and ChargingOpen2.Power and Ground Distribution β€” Electrical Diagrams > Power Supply Routing > Accessory Power Supply - Ignition Switch In "ACC" or "ON"Starting and ChargingOpen3.Power and Ground Distribution β€” Electrical Diagrams > Power Supply Routing > Battery Power Supply - Ignition Switch In Any PositionStarting and ChargingOpen4.Starting System β€” Connector Views > A/T ModelsStarting and ChargingOpen5.Starting System β€” Connector Views > M/T ModelsStarting and ChargingOpen6.Starting System β€” Diagnostic Aids > Consult Checking System > Consult Data Link Connector (DLC) CircuitStarting and ChargingOpen7.Starting System β€” Diagnostic Aids > Consult Checking System > Loading ProcedureStarting and ChargingOpen8.Starting System β€” Diagnostic Aids > Harness ConnectorsStarting and ChargingOpen9.Starting System β€” Diagnostic Aids > How to Check Terminal > Connector and Terminal Pin KitStarting and ChargingOpen10.Starting System β€” Diagnostic Aids > How to Check Terminal > Connector InspectionStarting and ChargingOpen11.Starting System β€” Diagnostic Aids > How to Check Terminal > How to Check Enlarged Contact Spring of TerminalStarting and ChargingOpen12.Starting System β€” Diagnostic Aids > How to Check Terminal > How to Probe ConnectorsStarting and ChargingOpen13.Starting System β€” Diagnostic Aids > How to Check Terminal > Probing From Harness SideStarting and ChargingOpen14.Starting System β€” Diagnostic Aids > How to Check Terminal > Probing From Terminal Side > Female TerminalStarting and ChargingOpen15.Starting System β€” Diagnostic Aids > How to Check Terminal > Probing From Terminal Side > Male TerminalStarting and ChargingOpen16.Starting System β€” Diagnostic Aids > How to Check Terminal > Terminal Lock InspectionStarting and ChargingOpen17.Starting System β€” Diagnostic Aids > How to Follow Flowchart In Trouble Diagnosis > Flow Chart ExampleStarting and ChargingOpen18.Starting System β€” Diagnostic Aids > How to Follow Flowchart In Trouble Diagnosis > How to Follow This FlowchartStarting and ChargingOpen19.Starting System β€” Diagnostic Aids > How to Follow Flowchart In Trouble Diagnosis > Key to Symbol Signifying Measurements or ProceduresStarting and ChargingOpen20.Starting System β€” Diagnostic Aids > Standardized RelaysStarting and ChargingOpen21.Starting System β€” Diagram Information and Instructions > Circuit Inspection > Ground InspectionStarting and ChargingOpen22.Starting System β€” Diagram Information and Instructions > Circuit Inspection > IntroductionStarting and ChargingOpen23.Starting System β€” Diagram Information and Instructions > Circuit Inspection > Testing For "OPENS" In the CircuitStarting and ChargingOpen24.Starting System β€” Diagram Information and Instructions > Circuit Inspection > Testing For "SHORTS" In the CircuitStarting and ChargingOpen25.Starting System β€” Diagram Information and Instructions > Circuit Inspection > Voltage Drop TestsStarting and ChargingOpen26.Starting System β€” Diagram Information and Instructions > Diagram InstructionsStarting and ChargingOpen27.Starting System β€” Diagram Information and Instructions > Ground Distribution Cell CodesStarting and ChargingOpen28.Starting System β€” Diagram Information and Instructions > How to Perform Efficient Diagnosis For an Electrical IncidentStarting and ChargingOpen29.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > Cold or Hot Start UpStarting and ChargingOpen30.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > Electrical LoadStarting and ChargingOpen31.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > FreezingStarting and ChargingOpen32.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > Heat SensitiveStarting and ChargingOpen33.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > IntroductionStarting and ChargingOpen34.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > Vehicle VibrationStarting and ChargingOpen35.Starting System β€” Diagram Information and Instructions > Incident Simulation Tests > Water IntrusionStarting and ChargingOpen36.Starting System β€” Diagram Information and Instructions > Sample Diagram InformationStarting and ChargingOpen37.Starting System β€” Diagram Information and Instructions > Wire Color Code IdentificationStarting and ChargingOpen38.Starting System β€” Diagram Information and Instructions > Wiring Diagram Codes (Cell Codes)Starting and ChargingOpen39.Starting System β€” Electrical Diagrams > A/T Model Wiring DiagramStarting and ChargingOpen40.Starting System β€” Electrical Diagrams > M/T Model Wiring DiagramStarting and ChargingOpen41.Components > Sensors > Crankshaft Position Sensor (OBD)GeneralOpen42.Connector Views > Battery Power Supply - Ignition Switch In Any PositionPower and Ground DistributionOpen43.Connector Views > Computers and Control Systems > Crankshaft Position SensorGeneralOpen44.Connector Views > Power and Ground Distribution > System Diagram > Battery Power Supply - Ignition Switch In Any PositionGeneralOpen45.Connector Views > Starting System > A/T ModelsGeneralOpen46.Connector Views > Starting System > M/T ModelsGeneralOpen47.Electrical Diagrams > Power and Ground Distribution > Power Supply Routing > Accessory Power Supply - Ignition Switch In "ACC" or "ON"GeneralOpen48.Electrical Diagrams > Power and Ground Distribution > Power Supply Routing > Battery Power Supply - Ignition Switch In Any PositionGeneralOpen

Parts & Tools for This Job

Common parts shoppers buy for 1998 Nissan-Datsun Altima GXE Starter.

As an Amazon Associate, AllOEMManuals earns from qualifying purchases. Prices and availability may vary.

Factory Service Tools

Turn This Into a Confident Next Step

Verify the likely fault first, then compare a quote before you approve expensive work.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.