P2096

Factory Manual References

Factory service manual diagnostic procedure for 2013 audi a8

01 Mil On, DTC P209600 And/Or P209800 Stored In ECM (GROUP 01, NO. 19-96)

Publication date: 2019-01-23
Reference number: GROUP 01, NO. 19-96
Supersedes refnos: 2046611/1, 2046611/2, 2046611/3, 2046611/4, 2046611/5, GROUP 01, NO. 17-02, GROUP 01, NO. 17-99, GROUP 01, NO. 18-85, GROUP 01, NO. 19-01

01 MIL ON, DTC P209600 AND/OR P209800 STORED IN ECM

01 MIL ON, DTC P209600 AND/OR P209800 STORED IN ECM

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 01, NO. 19-01 (2046611/5), Date of Issue:  January 23, 2019
AUDI: A8, S6, S7, S8, and RS 6 2013-2018; RS 7 2014-2018
GROUP: 01 - On-Board Diagnostic
Superceded Bulletin(s): GROUP 01, NO. 19-96, Date of Issue:  January 02, 2019

APPLICABLE MODELS AND YEARS

01 19 01 2046611/5 January 23, 2019. Supersedes Technical Service Bulletin Group 01 number 19-96 dated January 2, 2019 for reasons listed below.

APPLICABLE MODELS AND YEARS

Model(s) Year VIN Range Vehicle-Specific Equipment
A8, S6, S7, S8, and RS 6 2013 - 2018 All 4.0L
RS 7 2014 - 2018 All 4.0L

CONDITION

REVISION HISTORY

Revision Date Purpose
5 - Revised Required Parts and Tools  (Updated Part Numbers)
4 01/02/2019 Revised header (Added Model Years)
Revised Condition  (Updated information)
Revised Warranty  (Updated Labor Operations)
Revised Required  Parts and Tools (Updated Part Numbers)
3 09/07/2018 Revised header data (Added model years)

Customer statement: 

  • MIL on.

Workshop findings: 

The following DTCs are logged individually or in combination in the engine control module (ECM), J623 (address word 0001):

  • DTC P209600  (Post Catalyst Fuel Trim System Bank1 Too Lean).
  • DTC P209800  (Post Catalyst Fuel Trim System Bank2 Too Lean).

Any other DTCs regarding the oxygen sensors before the catalyst that may have been logged before or after the above DTCs should be ignored.

After performing a leakage test of the exhaust system, as part of the GFF test, the Guided Fault Finding recommends the replacement of the oxygen sensor before the catalyst. Do not replace the front oxygen sensor. 

TECHNICAL BACKGROUND

The internal reference duct of the oxygen sensor after  the catalyst has been contaminated.

PRODUCTION SOLUTION

Not applicable.

SERVICE

Replace the oxygen sensor after the catalyst  of the affected bank only, according to the DTC fault memory. The replacement of the oxygen sensors before the catalyst are not required. 

Ensure that the correct sensor per the GFF DTC fault memory is installed. Reference ElsaPro for the locations.

WARRANTY

WARRANTY INFORMATION

Claim Type: 
  • 110 up to 48 Months/50,000 Miles.
  • G10 for CPO Covered Vehicles - Verify Owner.
  • If vehicle is outside any warranty, this Technical Service Bulletin is informational only.
Service Number:  2473
Damage Code:  0040
Labor Operations:  Oxygen sensor after catalyst G130 (Bank1) 2473 1921 See SRT
Oxygen sensor after catalyst G131 (Bank2) 2473 1922 See SRT
Oxygen sensors after catalyst (only if both DTC are present in current GFF log) 2473 2021 See SRT
Diagnostic Time:  GFF 0150 0000 Time stated on diagnostic protocol (20 TU Max)
Road test prior to service procedure No allowance 0 TU
Road test after service procedure 0121 0004 10 TU
Claim Comment:  As per TSB #2046611/5

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual.  Claims are subject to review or audit by Audi Warranty.

REQUIRED PARTS AND TOOLS

Always check with your Parts Department and/or ETKA for the latest information and parts bulletins.

PARTS INFORMATION

Part Number Part Description Quantity
4H0906262L Oxygen sensor after catalyst G130 (Bank1) 01
4H0906262M Oxygen sensor after catalyst G131 (Bank2) 01
See ETKA Fasteners, Bolts, Nuts and Screws as needed per the Repair Manual See ETKA/ELSA

ADDITIONAL INFORMATION

All parts and service references provided in this TSB (2046611) are subject to change and/or removal.

©2019 Audi of America, Inc.  All rights reserved. Information contained in this document is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher.

Supporting Diagrams & Locations

Reference material from the factory manual for this diagnostic procedure.

Location

00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)

Location

00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)

Location

00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)

Location

00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)

Fuse/Relay

00 SOFTWARE Version Management (SVM), Operating Instructions - 00 12 32

Fuse/Relay

00 SOFTWARE Version Management (SVM), Operating Instructions - 00 12 32

Fuse/Relay

00 SOFTWARE Version Management (SVM), Operating Instructions - 00 12 32

Fuse/Relay

00 SOFTWARE Version Management (SVM), Operating Instructions - 00 12 32

Related Procedures

Procedure

105000 MI or 168000 KM

Procedure

105000 MI or 168000 KM

Procedure

105000 MI or 168000 KM

Procedure

105000 MI or 168000 KM

Procedure

105000 MI or 168000 KM