01 Mil On, Cold Start Misfire (Misfire DTCS P0300-P0306 In ECM) (2024632)
Reference number: 2024632
01 MIL ON, COLD START MISFIRE (MISFIRE DTCS P0300-P0306 IN ECM)
TECHNICAL SERVICE BULLETIN
| AUDI: | A4, A6 |
CONDITION
- MIL on.
- Misfire DTCs (P0300, P0301, P0302, P0303, P0304, P0305 or P0306) are stored in the ECM.
- Freeze frame data indicates DTCs stored during cold start (engine coolant temperature between 18 - 36°C).
TECHNICAL BACKGROUND
Software update is needed.
PRODUCTION SOLUTION
New software in the 4F2 910 559 H Control Module (J623) addressed the condition.
SERVICE
- Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.
- Update the ECM using the SVM action code as listed in the table below, if necessary.
- Perform a short test drive.
- Verify repair during cold start next morning via recording MVB 14 and 15 (ambient temperature between 50 - 80°F).
Tip: Based on normal fuel quality variation under certain ambient conditions some single misfires may be recorded during cold start (catalytic converter heating phase). This will have no negative effect, no further investigation is needed.
| Model | Engine and/or Transmission | Old Software Part Number | Old Software Version | New Software Part Number | New Software Version (or higher) | SVM Action Code |
|---|---|---|---|---|---|---|
| A6 MY08/09 | 3.2 V6 FSI | 4F2 910559 H | 0020 | 4F2 910559 H | 0040 | 01A029 |
| A6 MY07 | 3.2 V6 FSI | 4F2 910559 C | 0020 | 4F2910559C | 0070 | |
| A4 (8E, 8H) | 3.2 V6 FSI | 8E1910559F | 0060 | 8E1910559F | 0070 |
WARRANTY
| Claim Type: | Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only. | ||
| Service Number: | 2470 | ||
| Damage Code: | 0039 | ||
| Labor Operations: | Check software levels, no update necessary | 2470 01 99 | 20 TU |
| Check software levels, perform update | 2470 25 99 | 60 TU | |
| Diagnostic Time: | GFF - Checking and clearing fault codes included in existing labor operations | No allowance | 0 TU |
| Road test prior to service procedure | 0121 0002 | 10 TU | |
| Road test after service procedure | 0121 0004 | 10 TU | |
| Technical diagnosis at dealer's discretion (Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details) |
|||
| Claim Comment: | As per TSB #2024632/3 | ||
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty.
ADDITIONAL INFORMATION
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information.
ATTACHMENT
01 Mil On, Cold Start Misfire (Misfire DTCS P0300-P0306 In ECM) (2024632)
Reference number: 2024632
01 MIL ON, COLD START MISFIRE (MISFIRE DTCS P0300-P0306 IN ECM)
TECHNICAL SERVICE BULLETIN
| AUDI: | A4, A6 |
CONDITION
- MIL on.
- Misfire DTCs (P0300, P0301, P0302, P0303, P0304, P0305 or P0306) are stored in the ECM.
- Freeze frame data indicates DTCs stored during cold start (engine coolant temperature between 18 - 36°C).
TECHNICAL BACKGROUND
Software update is needed.
PRODUCTION SOLUTION
New software in the 4F2 910 559 H Control Module (J623) addressed the condition.
SERVICE
- Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.
- Update the ECM using the SVM action code as listed in the table below, if necessary.
- Perform a short test drive.
- Verify repair during cold start next morning via recording MVB 14 and 15 (ambient temperature between 50 - 80°F).
Tip: Based on normal fuel quality variation under certain ambient conditions some single misfires may be recorded during cold start (catalytic converter heating phase). This will have no negative effect, no further investigation is needed.
| Model | Engine and/or Transmission | Old Software Part Number | Old Software Version | New Software Part Number | New Software Version (or higher) | SVM Action Code |
|---|---|---|---|---|---|---|
| A6 MY08/09 | 3.2 V6 FSI | 4F2 910559 H | 0020 | 4F2 910559 H | 0040 | 01A029 |
| A6 MY07 | 3.2 V6 FSI | 4F2 910559 C | 0020 | 4F2910559C | 0070 | |
| A4 (8E, 8H) | 3.2 V6 FSI | 8E1910559F | 0060 | 8E1910559F | 0070 |
WARRANTY
| Claim Type: | Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only. | ||
| Service Number: | 2470 | ||
| Damage Code: | 0039 | ||
| Labor Operations: | Check software levels, no update necessary | 2470 01 99 | 20 TU |
| Check software levels, perform update | 2470 25 99 | 60 TU | |
| Diagnostic Time: | GFF - Checking and clearing fault codes included in existing labor operations | No allowance | 0 TU |
| Road test prior to service procedure | 0121 0002 | 10 TU | |
| Road test after service procedure | 0121 0004 | 10 TU | |
| Technical diagnosis at dealer's discretion (Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details) |
|||
| Claim Comment: | As per TSB #2024632/3 | ||
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty.
ADDITIONAL INFORMATION
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information.
ATTACHMENT
01 Mil On, Cold Start Misfire (Misfire DTCS P0300-P0306 In ECM) (2024632)
Reference number: 2024632
01 MIL ON, COLD START MISFIRE (MISFIRE DTCS P0300-P0306 IN ECM)
TECHNICAL SERVICE BULLETIN
| AUDI: | A4, A6 |
CONDITION
- MIL on.
- Misfire DTCs (P0300, P0301, P0302, P0303, P0304, P0305 or P0306) are stored in the ECM.
- Freeze frame data indicates DTCs stored during cold start (engine coolant temperature between 18 - 36°C).
TECHNICAL BACKGROUND
Software update is needed.
PRODUCTION SOLUTION
New software in the 4F2 910 559 H Control Module (J623) addressed the condition.
SERVICE
- Follow all instructions in the attached TSB 2011732 00 Software Version Management (SVM), operating instructions.
- Update the ECM using the SVM action code as listed in the table below, if necessary.
- Perform a short test drive.
- Verify repair during cold start next morning via recording MVB 14 and 15 (ambient temperature between 50 - 80°F).
Tip: Based on normal fuel quality variation under certain ambient conditions some single misfires may be recorded during cold start (catalytic converter heating phase). This will have no negative effect, no further investigation is needed.
| Model | Engine and/or Transmission | Old Software Part Number | Old Software Version | New Software Part Number | New Software Version (or higher) | SVM Action Code |
|---|---|---|---|---|---|---|
| A6 MY08/09 | 3.2 V6 FSI | 4F2 910559 H | 0020 | 4F2 910559 H | 0040 | 01A029 |
| A6 MY07 | 3.2 V6 FSI | 4F2 910559 C | 0020 | 4F2910559C | 0070 | |
| A4 (8E, 8H) | 3.2 V6 FSI | 8E1910559F | 0060 | 8E1910559F | 0070 |
WARRANTY
| Claim Type: | Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only. | ||
| Service Number: | 2470 | ||
| Damage Code: | 0039 | ||
| Labor Operations: | Check software levels, no update necessary | 2470 01 99 | 20 TU |
| Check software levels, perform update | 2470 25 99 | 60 TU | |
| Diagnostic Time: | GFF - Checking and clearing fault codes included in existing labor operations | No allowance | 0 TU |
| Road test prior to service procedure | 0121 0002 | 10 TU | |
| Road test after service procedure | 0121 0004 | 10 TU | |
| Technical diagnosis at dealer's discretion (Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details) |
|||
| Claim Comment: | As per TSB #2024632/3 | ||
All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty.
ADDITIONAL INFORMATION
All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information.
ATTACHMENT
Supporting Diagrams & Locations
Reference material from the factory manual for this diagnostic procedure.
00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)
00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)
00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)
00 Software Version Management (SVM), Operating Instructions (GROUP 00, NO. 21-55)