3.2FSI - Mil On With DTC'S Stored For Camshaft Adjustment (GROUP 15, NO. 08-13)
Publication date: 2008-11-20
Reference number: GROUP 15, NO. 08-13
Supersedes refnos: 2012630, GROUP 15, NO. 06-02, GROUP 15, NO. 06-04
3.2FSI - MIL ON WITH DTC'S STORED FOR CAMSHAFT ADJUSTMENT
Reference number: GROUP 15, NO. 08-13
Supersedes refnos: 2012630, GROUP 15, NO. 06-02, GROUP 15, NO. 06-04
3.2FSI - MIL ON WITH DTC'S STORED FOR CAMSHAFT ADJUSTMENT
TECHNICAL SERVICE BULLETIN
Reference Number(s): GROUP 15, NO. 08-13 (2012630/3), Date of Issue:
November 20, 2008
Superceded Bulletin(s): GROUP 15, NO. 06-04, Date of Issue:
September 13, 2006
| AUDI: | A4 2005-2006; A6 2005-2006 |
| GROUP: | 15 - Engine - Cylinder Heads Valve Drive |
SERVICE INFORMATION
15 08 13 2012630/3 November 20, 2008. Supersedes Technical Service Bulletin Group 15 number 06-04 dated September 13, 2006.
APPLICABLE MODELS AND YEARS
| Model(s) | Year | Eng. Code | Trans. Code | VIN Range From | VIN Range To |
|---|---|---|---|---|---|
| A4 | 2005 | BKH | N/A | 8E_5A400000 | 8E_5A999999 |
| A4 | 2006 | BKH | N/A | 8E_6A000000 | 8E_6A250431 |
| A6 | 2005 | BKH | N/A | 4F_5N000000 | 4F_5N999999 |
| A6 | 2006 | BKH | N/A | 4F_6N000000 | 4F_6N163525 |
CONDITION
MIL on and one or more of the following DTC's are stored:
DIAGNOSTIC TROUBLE CODES
| DTC | DTC Description |
|---|---|
| P0014 | B Camshaft Position (Bank 1) - Timing over-advanced or System Performance |
| P0024 | B Camshaft Position (Bank 2) - Timing over-advanced or System Performance |
| P0366 | Camshaft Position Sensor Circuit (Bank 1) - Range/Performance |
| P0346 | Camshaft Position Sensor Circuit (Bank 2) - Range/Performance |
TECHNICAL BACKGROUND
The condition can be caused by one or more jammed Camshaft Adjustment Solenoid Valve(s) (N205/N208/N318/N319). This may be due to contamination (e.g. debris) of the Hydraulic Mechanism of the Solenoid Valve(s).
PRODUCTION SOLUTION
Not applicable.
SERVICE
- Remove the affected Camshaft Adjustment Solenoid Valve(s).
- Thoroughly inspect the Hydraulic Mechanism of the Solenoid Valve(s) and its mounting location in the cylinder head for any debris.
If there is any debris inside the Hydraulic Mechanism:
- Replace affected Solenoid Valve(s) and clean out its mounting location in the cylinder head thoroughly.
- DO NOT replace the Camshaft Adjusters!
If there is no debris present inside the Hydraulic Mechanism:
- Check the correct function of the Camshaft Position Sensor(s) (G40/G163/G300/G301) of the affected camshaft(s) with Guided Fault Finding.
- Follow Guided Fault Finding for further Diagnosis.
WARRANTY
WARRANTY INFORMATION
| When procedure applies to vehicles within the New Vehicle Limited Warranty, use the following: | |||
| Claim Type: | W2 | ||
| Part Identifier: | 1585 | ||
| Damage Code: | 1585 17 XXXX | ||
| Labor Operations: | Refer to ElsaWeb for Suggested Repair Times | ||
| Diagnostic Time: | No Diagnostic Time Allowed. | ||
| Claim Comment: | As per TSB #2012630/3. | ||
| All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual. Claims are subject to review or audit by Audi Warranty. | |||
REQUIRED PARTS AND TOOLS
PARTS INFORMATION
| Part Number | Part Description | Qty |
|---|---|---|
| 06E 109 257 F | Control Valve | based on need |
| 06E 109 257 J | Control Valve | based on need |
All part and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Dept. and service manuals for the latest information.