P0101

Factory Manual References

Factory service manual diagnostic procedure for 2004 audi a8

Mil On (Mass Airflow Sensor DTCS P0101, P0102, P0103, P0112, P0113 In ECM) (GROUP 24, NO. 10-35)

Publication date: 2010-06-17
Reference number: GROUP 24, NO. 10-35
Supersedes refnos: 2014521, GROUP 24, NO. 08-04, GROUP 24, NO. 08-49, GROUP 24, NO. 09-16

MIL ON (MASS AIRFLOW SENSOR DTCS P0101, P0102, P0103, P0112, P0113 IN ECM)

MIL ON (MASS AIRFLOW SENSOR DTCS P0101, P0102, P0103, P0112, P0113 IN ECM)

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 24, NO. 10-35 (2014521/5), Date of Issue:  June 17, 2010
AUDI: S4 2004 - 2007; S4 Cabriolet 2005 - 2007; RS6 2003 - 2004; allroad 2004 - 2005; A8 2004 - 2005, 2006
GROUP: 24 - Multiport Fuel Injection
Superceded Bulletin(s): GROUP 24, NO. 09-16, Date of Issue:  August 7, 2009

SUBJECT

MIL on (Mass airflow sensor DTCs P0101, P0102, P0103, P0112, P0113 in ECM) 

24 10 35 2014521/5 June 17, 2010. Supersedes Technical Service Bulletin Group 24 number 09-16 dated August 7, 2009.

APPLICABLE MODELS AND YEARS

Model(s) Year VIN Range Vehicle-Specific Equipment
S4 2004 - 2007 All Engine Code BHF
S4 Cabriolet 2005 - 2007 900001 - 999999 Engine Code BHF
RS6 2003 - 2004 900001 - 999999 Engine Code BCY
allroad 2004 - 2005 All Engine Code BAS
A8 2004 - 2005 All Engine Code BFM
2006 All Engine Code BGK

CONDITION

  • MIL on.
  • Engine has low performance without significant loss of power or stalling.

TECHNICAL BACKGROUND

DTCs related to the Mass Air Flow Sensor and fuel trim faults can be related to (but not limited to) the following conditions:

  • False intake air, or air filter element very dirty.
  • Fuel pressure too low.
  • Mass Air Flow Sensor fault. Possible fault entries associated with this condition:
    • DTC 16485  (P0101 Mass or Volume Air Flow Circuit Range/Performance).
    • DTC 16486  (P0102 Mass or Volume Air Flow Circ. Low Input).
    • DTC 16487  (P0103 Mass or Volume Air Flow Circ. High Input).
    • DTC 16496  (P0112 Intake Air Temp.Circ. Low Input).
    • DTC 16497  (P0113 Intake Air Temp.Circ. High Input).

PRODUCTION SOLUTION

No measures necessary.

SERVICE

  1. Ensure one of the previously listed DTCs are logged. Verify this using the GFF test.
    • A replacement of the Mass Air Flow Sensor-G70 is only permitted if one of the above fault entries is logged and verified using the GFF test.
    • If there is no fault entry for the Mass Air Flow Sensor, carry out the following checks and GFF tests related to the DTCs in ECM fault memory.
  2. Check air filter installation. The air filter must be the factory air filter element that is clean, dry and properly seated in the air box assembly.
  3. Check fuel pressure per procedure in ElsaWeb.
    • With too high fuel pressure, the mixture adaptation value is smaller than normal.
    • With too low fuel pressure, the mixture adaptation value is larger than normal.
  4. Check the mixture adaptation values in the measured value block of the engine control unit 032 (idle speed: values 1+3/part load: values 2+4).
    • Values 1+3 should be +/- 2.5% and values 2+4 +/-10%.
  5. Check the intake system for false air with leak detection spray G 001 800 A1. 

    The leak detection spray is drawn in with false air through vacuum into the intake system. The leak detection spray reduces the ignitability of the air/fuel mixture. This leads to a drop in engine RPM and a change in oxygen sensor values.

    With false intake air, the actual lambda value MVB 031/value 1+3 goes up and the lambda control value MVB 033/value 1+3 goes down.

WARRANTY

WARRANTY INFORMATION

Claim Type:  Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only.
Service Number:  2445
Damage Code:  0010
Labor Operations:  Replace Mass Air Flow Sensor G70 - S4/S4 Cabrio 2445 19 31 30 TU
Replace Mass Air Flow Sensor G70 - allroad 2445 19 29 40 TU
Replace Mass Air Flow Sensor G70 or G246- RS 6 2445 19 27 70 TU
Replace Mass Air Flow Sensor both G70 and G246 - RS 6 2445 20 28 70 TU
Replace Mass Air Flow Sensor G70 - A8 2445 19 29 70 TU
Diagnostic Time:  GFF 0150 0000 Time stated on diagnostic protocol
Road test prior to service procedure 0121 0002 10 TU
Road test after service procedure 0121 0004 10 TU
Technical diagnosis at dealer's discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:  As per TSB #2014521/5

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual.  Claims are subject to review or audit by Audi Warranty.

ADDITIONAL INFORMATION

More information on this system can be found in the following resources:

  • ElsaWeb: TSB 2010064 24 Engine Intake Manifold Mounting Bolt Torque
  • ElsaWeb: TSB 2010221 01 MIL on (DTC P1127, P1129, P1136 & P1138)
  • ElsaWeb: TSB 2014753 01 MIL on, gasoline quality (DTC P0300 or P030x, lean condition DTCs)

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information.

Mil On (Mass Airflow Sensor DTCS P0101, P0102, P0103, P0112, P0113 In ECM) (GROUP 24, NO. 10-35)

Publication date: 2010-06-17
Reference number: GROUP 24, NO. 10-35
Supersedes refnos: 2014521, GROUP 24, NO. 08-04, GROUP 24, NO. 08-49, GROUP 24, NO. 09-16

MIL ON (MASS AIRFLOW SENSOR DTCS P0101, P0102, P0103, P0112, P0113 IN ECM)

MIL ON (MASS AIRFLOW SENSOR DTCS P0101, P0102, P0103, P0112, P0113 IN ECM)

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 24, NO. 10-35 (2014521/5), Date of Issue:  June 17, 2010
AUDI: S4 2004 - 2007; S4 Cabriolet 2005 - 2007; RS6 2003 - 2004; allroad 2004 - 2005; A8 2004 - 2005, 2006
GROUP: 24 - Multiport Fuel Injection
Superceded Bulletin(s): GROUP 24, NO. 09-16, Date of Issue:  August 7, 2009

SUBJECT

MIL on (Mass airflow sensor DTCs P0101, P0102, P0103, P0112, P0113 in ECM) 

24 10 35 2014521/5 June 17, 2010. Supersedes Technical Service Bulletin Group 24 number 09-16 dated August 7, 2009.

APPLICABLE MODELS AND YEARS

Model(s) Year VIN Range Vehicle-Specific Equipment
S4 2004 - 2007 All Engine Code BHF
S4 Cabriolet 2005 - 2007 900001 - 999999 Engine Code BHF
RS6 2003 - 2004 900001 - 999999 Engine Code BCY
allroad 2004 - 2005 All Engine Code BAS
A8 2004 - 2005 All Engine Code BFM
2006 All Engine Code BGK

CONDITION

  • MIL on.
  • Engine has low performance without significant loss of power or stalling.

TECHNICAL BACKGROUND

DTCs related to the Mass Air Flow Sensor and fuel trim faults can be related to (but not limited to) the following conditions:

  • False intake air, or air filter element very dirty.
  • Fuel pressure too low.
  • Mass Air Flow Sensor fault. Possible fault entries associated with this condition:
    • DTC 16485  (P0101 Mass or Volume Air Flow Circuit Range/Performance).
    • DTC 16486  (P0102 Mass or Volume Air Flow Circ. Low Input).
    • DTC 16487  (P0103 Mass or Volume Air Flow Circ. High Input).
    • DTC 16496  (P0112 Intake Air Temp.Circ. Low Input).
    • DTC 16497  (P0113 Intake Air Temp.Circ. High Input).

PRODUCTION SOLUTION

No measures necessary.

SERVICE

  1. Ensure one of the previously listed DTCs are logged. Verify this using the GFF test.
    • A replacement of the Mass Air Flow Sensor-G70 is only permitted if one of the above fault entries is logged and verified using the GFF test.
    • If there is no fault entry for the Mass Air Flow Sensor, carry out the following checks and GFF tests related to the DTCs in ECM fault memory.
  2. Check air filter installation. The air filter must be the factory air filter element that is clean, dry and properly seated in the air box assembly.
  3. Check fuel pressure per procedure in ElsaWeb.
    • With too high fuel pressure, the mixture adaptation value is smaller than normal.
    • With too low fuel pressure, the mixture adaptation value is larger than normal.
  4. Check the mixture adaptation values in the measured value block of the engine control unit 032 (idle speed: values 1+3/part load: values 2+4).
    • Values 1+3 should be +/- 2.5% and values 2+4 +/-10%.
  5. Check the intake system for false air with leak detection spray G 001 800 A1. 

    The leak detection spray is drawn in with false air through vacuum into the intake system. The leak detection spray reduces the ignitability of the air/fuel mixture. This leads to a drop in engine RPM and a change in oxygen sensor values.

    With false intake air, the actual lambda value MVB 031/value 1+3 goes up and the lambda control value MVB 033/value 1+3 goes down.

WARRANTY

WARRANTY INFORMATION

Claim Type:  Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only.
Service Number:  2445
Damage Code:  0010
Labor Operations:  Replace Mass Air Flow Sensor G70 - S4/S4 Cabrio 2445 19 31 30 TU
Replace Mass Air Flow Sensor G70 - allroad 2445 19 29 40 TU
Replace Mass Air Flow Sensor G70 or G246- RS 6 2445 19 27 70 TU
Replace Mass Air Flow Sensor both G70 and G246 - RS 6 2445 20 28 70 TU
Replace Mass Air Flow Sensor G70 - A8 2445 19 29 70 TU
Diagnostic Time:  GFF 0150 0000 Time stated on diagnostic protocol
Road test prior to service procedure 0121 0002 10 TU
Road test after service procedure 0121 0004 10 TU
Technical diagnosis at dealer's discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:  As per TSB #2014521/5

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual.  Claims are subject to review or audit by Audi Warranty.

ADDITIONAL INFORMATION

More information on this system can be found in the following resources:

  • ElsaWeb: TSB 2010064 24 Engine Intake Manifold Mounting Bolt Torque
  • ElsaWeb: TSB 2010221 01 MIL on (DTC P1127, P1129, P1136 & P1138)
  • ElsaWeb: TSB 2014753 01 MIL on, gasoline quality (DTC P0300 or P030x, lean condition DTCs)

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information.

Mil On (Mass Airflow Sensor DTCS P0101, P0102, P0103, P0112, P0113 In ECM) (GROUP 24, NO. 10-35)

Publication date: 2010-06-17
Reference number: GROUP 24, NO. 10-35
Supersedes refnos: 2014521, GROUP 24, NO. 08-04, GROUP 24, NO. 08-49, GROUP 24, NO. 09-16

MIL ON (MASS AIRFLOW SENSOR DTCS P0101, P0102, P0103, P0112, P0113 IN ECM)

MIL ON (MASS AIRFLOW SENSOR DTCS P0101, P0102, P0103, P0112, P0113 IN ECM)

TECHNICAL SERVICE BULLETIN

Reference Number(s): GROUP 24, NO. 10-35 (2014521/5), Date of Issue:  June 17, 2010
AUDI: S4 2004 - 2007; S4 Cabriolet 2005 - 2007; RS6 2003 - 2004; allroad 2004 - 2005; A8 2004 - 2005, 2006
GROUP: 24 - Multiport Fuel Injection
Superceded Bulletin(s): GROUP 24, NO. 09-16, Date of Issue:  August 7, 2009

SUBJECT

MIL on (Mass airflow sensor DTCs P0101, P0102, P0103, P0112, P0113 in ECM) 

24 10 35 2014521/5 June 17, 2010. Supersedes Technical Service Bulletin Group 24 number 09-16 dated August 7, 2009.

APPLICABLE MODELS AND YEARS

Model(s) Year VIN Range Vehicle-Specific Equipment
S4 2004 - 2007 All Engine Code BHF
S4 Cabriolet 2005 - 2007 900001 - 999999 Engine Code BHF
RS6 2003 - 2004 900001 - 999999 Engine Code BCY
allroad 2004 - 2005 All Engine Code BAS
A8 2004 - 2005 All Engine Code BFM
2006 All Engine Code BGK

CONDITION

  • MIL on.
  • Engine has low performance without significant loss of power or stalling.

TECHNICAL BACKGROUND

DTCs related to the Mass Air Flow Sensor and fuel trim faults can be related to (but not limited to) the following conditions:

  • False intake air, or air filter element very dirty.
  • Fuel pressure too low.
  • Mass Air Flow Sensor fault. Possible fault entries associated with this condition:
    • DTC 16485  (P0101 Mass or Volume Air Flow Circuit Range/Performance).
    • DTC 16486  (P0102 Mass or Volume Air Flow Circ. Low Input).
    • DTC 16487  (P0103 Mass or Volume Air Flow Circ. High Input).
    • DTC 16496  (P0112 Intake Air Temp.Circ. Low Input).
    • DTC 16497  (P0113 Intake Air Temp.Circ. High Input).

PRODUCTION SOLUTION

No measures necessary.

SERVICE

  1. Ensure one of the previously listed DTCs are logged. Verify this using the GFF test.
    • A replacement of the Mass Air Flow Sensor-G70 is only permitted if one of the above fault entries is logged and verified using the GFF test.
    • If there is no fault entry for the Mass Air Flow Sensor, carry out the following checks and GFF tests related to the DTCs in ECM fault memory.
  2. Check air filter installation. The air filter must be the factory air filter element that is clean, dry and properly seated in the air box assembly.
  3. Check fuel pressure per procedure in ElsaWeb.
    • With too high fuel pressure, the mixture adaptation value is smaller than normal.
    • With too low fuel pressure, the mixture adaptation value is larger than normal.
  4. Check the mixture adaptation values in the measured value block of the engine control unit 032 (idle speed: values 1+3/part load: values 2+4).
    • Values 1+3 should be +/- 2.5% and values 2+4 +/-10%.
  5. Check the intake system for false air with leak detection spray G 001 800 A1. 

    The leak detection spray is drawn in with false air through vacuum into the intake system. The leak detection spray reduces the ignitability of the air/fuel mixture. This leads to a drop in engine RPM and a change in oxygen sensor values.

    With false intake air, the actual lambda value MVB 031/value 1+3 goes up and the lambda control value MVB 033/value 1+3 goes down.

WARRANTY

WARRANTY INFORMATION

Claim Type:  Use applicable claim type. If vehicle is outside any warranty, this Technical Service Bulletin is informational only.
Service Number:  2445
Damage Code:  0010
Labor Operations:  Replace Mass Air Flow Sensor G70 - S4/S4 Cabrio 2445 19 31 30 TU
Replace Mass Air Flow Sensor G70 - allroad 2445 19 29 40 TU
Replace Mass Air Flow Sensor G70 or G246- RS 6 2445 19 27 70 TU
Replace Mass Air Flow Sensor both G70 and G246 - RS 6 2445 20 28 70 TU
Replace Mass Air Flow Sensor G70 - A8 2445 19 29 70 TU
Diagnostic Time:  GFF 0150 0000 Time stated on diagnostic protocol
Road test prior to service procedure 0121 0002 10 TU
Road test after service procedure 0121 0004 10 TU
Technical diagnosis at dealer's discretion
(Refer to Section 2.2.1.2 and Audi Warranty Online for DADP allowance details)
Claim Comment:  As per TSB #2014521/5

All warranty claims submitted for payment must be in accordance with the Audi Warranty Policies and Procedures Manual.  Claims are subject to review or audit by Audi Warranty.

ADDITIONAL INFORMATION

More information on this system can be found in the following resources:

  • ElsaWeb: TSB 2010064 24 Engine Intake Manifold Mounting Bolt Torque
  • ElsaWeb: TSB 2010221 01 MIL on (DTC P1127, P1129, P1136 & P1138)
  • ElsaWeb: TSB 2014753 01 MIL on, gasoline quality (DTC P0300 or P030x, lean condition DTCs)

All parts and service references provided in this TSB are subject to change and/or removal. Always check with your Parts Department and service manuals for the latest information.

Supporting Diagrams & Locations

Reference material from the factory manual for this diagnostic procedure.

Diagram

Digital Sound System Control Module 2 Harness Connectors, Bang and Olufsen

Diagram

Digital Sound System Control Module Harness Connectors, Bang and Olufsen

Diagram

Digital Sound System Control Module Harness Connectors, BOSE

Diagram

Digital Sound System Control Module Harness Connectors, BOSE 6000

Diagram

Diagrams

Location

CHRYSLER Group LLC

Location

Ford Motor Co.

Location

General Motors

Location

CHRYSLER Group LLC

Fuse/Relay

Diagnostic Trouble Codes (DTC) Index

Fuse/Relay

CHRYSLER Group LLC

Fuse/Relay

General Motors

Fuse/Relay

Ford Motor Co.

Related Procedures

Procedure

Air Bags:Frontal (06V324000)

Procedure

BLUETOOTH Disabling While Performing Module Updates (CTT 01-14-03)

Procedure

Airbag System, Servicing (GROUP 69, NO. 08-06)

Procedure

All Models, 02 Sensor DTCS (CTT 01-14-01)

Procedure

BLUETOOTH Disabling While Performing Module Updates (CTT 01-14-03)

Procedure

BLUETOOTH Disabling While Performing Module Updates (CTT 01-14-03)

← Back to 2004 audi a8General P0101 InfoDIY Repair Guides