DIY repair guide for 2005 Scion Tc
How to Replace the Starter on a 2005 Scion Tc
How to Replace the Starter on a 2005 Scion Tc. The quick answer is below, then the longer procedure, parts, and factory references.
Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Quick answer
Starter jobs start with the no-crank diagnosis
This page keeps the click/no-crank symptom, battery follow-up, and access steps near the top so owners can decide quickly if the starter is the real problem.
Direct answer
Confirm the starter before you order
2005 Scion Tc starter jobs are usually decided by symptom pattern, battery health, and access path.
- • Starter part: Starter motor
- • Use the click/no-crank symptom before replacing the starter.
- • Check battery condition, wiring connections, and the mounting area first.
- • Plan for under-vehicle access on many layouts and clean the mounting surface for a strong ground.
Before you order
Match the starter fitment and access path
Starter access is labor-heavy on many vehicles, so verifying engine and transmission fitment first saves the most wasted time.
- • Match engine and transmission before checkout.
- • Confirm mounting ear count and electrical terminal layout.
- • Plan access first because this job often starts under the vehicle.
Next step
Keep the battery and charging pages nearby
A weak battery or charging system can mimic a starter problem, so the follow-up pages matter here.
- • Use the battery page if the symptom started after low voltage or a dead battery.
- • Use the alternator page if the charging light or battery warning is part of the story.
Exact-fit quick check
2005 tC 2.4L Starter — Driver-Side Bellhousing, Remove Intake Duct
The 2005 Scion tC uses Toyota's 2AZ-FE 2.4L engine with the starter mounted on the driver side of the transaxle bellhousing. The air intake resonator duct blocks the upper bolt — remove it first. This is a straightforward 90-minute job with basic hand tools.
Starter is mounted on the driver (left) side of the transaxle bellhousing, below the intake manifold and behind the battery tray area
OEM starter part number: 28100-28041 (Toyota) or 28100-0H080; aftermarket: Denso 280-0329 reman or TYC 1-17930 — verify 12V, 1.4 kW, 9-tooth pinion
Upper bolt: 14mm x 1.5 x 50mm, torque to 29 ft-lb; lower bolt: 14mm x 1.5 x 45mm, torque to 29 ft-lb — both accessible with a 14mm deep socket and 6-inch extension
Remove the air intake resonator duct (1 hose clamp, 2 plastic clips) and the battery hold-down bracket for clear upper bolt access from above
B+ cable nut at solenoid: 12mm; S-terminal wire: push-on spade with lock tab — squeeze tab and pull straight to avoid breaking the connector
The 2AZ-FE uses a composite oil pan — do NOT rest the car on a floor jack under the oil pan; use the front subframe lift point behind the radiator
If starter clicks but doesn't crank, tap the solenoid body with a hammer while a helper holds the key to START — if it cranks, the solenoid contacts are worn (common at 120K+ miles)
Exact-fit parts
Parts You'll Need
Vehicle-specific part numbers and quantities pulled from the factory service manual data for this repair.
Toyota reman; Denso 280-0329 or TYC 1-17930 equivalent
14mm flange bolts, replace if stretched
10mm J-bolt, easy to lose
Replace if corroded; 8mm socket or flathead screwdriver
Coat B+ terminal and spade connector
Shop prep
Tools Required
Gather these exact sizes and tools before you start — the manual calls each one out for a reason.
Socket set
10mm, 12mm, 14mm · 14mm deep socket for starter bolts; 12mm for B+ nut
Ratchet and extension
3/8-inch drive, 6-inch extension · For upper starter bolt
Torque wrench
3/8-inch drive, 10-80 ft-lb · 29 ft-lb on starter bolts
Multimeter
N/A · Test voltage at S-terminal during crank
Pry bar
12-inch · Gently break starter free from dowel pins
Safety-critical values
Torque Specifications
These are factory torque values from the OEM service manual. Overtightening can strip threads; undertightening can cause leaks or component failure.
| Component | Torque Value |
|---|---|
| Starter mounting bolts | 29 ft-lb |
| Battery negative terminal | 4.3 ft-lb |
How this page is grounded
The answer starts from a structured repair template, then narrows to the exact vehicle, task, fitment notes, and linked manual paths already available for this page.
Exact vehicle context
This page only renders after the year, make, model, and task are validated into a real repair path.
Structured repair data
The page pulls from repair timing, tools, parts, warnings, and step data before it renders the guide body.
Manual and spec cross-checks
Use the linked manual and spec paths to verify fitment, torque, and service order before teardown.
Related Pages
More resources for this repair
Browse related vehicle pages, model guides, and other starter replacement resources.
Symptom routing
Priority symptom hubs that lead to this repair
These report-backed symptom hubs are the strongest plain-English entry points into this repair path, related codes, and exact vehicle troubleshooting.
Code reinforcement
Related Trouble Codes
These check engine light codes are often connected to this repair.
Engine Code
P0010: Intake Camshaft Position Actuator Circuit (Bank 1)
Promote from symptom hubs and repair pages
Promote from symptom hubs and repair pages
Engine Code
P0011: Intake Camshaft Position Timing Over-Advanced (Bank 1)
Promote from symptom hubs and repair pages
Promote from symptom hubs and repair pages
Engine Code
P0012: Intake Camshaft Position Timing Over-Retarded (Bank 1)
Promote from symptom hubs and repair pages
Promote from symptom hubs and repair pages
Engine Code
P0013: Exhaust Camshaft Position Actuator Circuit (Bank 1)
Promote from symptom hubs and repair pages
Promote from symptom hubs and repair pages
Best first step for this repair
Check starter fitment now
Starter access is labor-heavy on many vehicles, so verifying engine and transmission fitment first saves the most wasted time.
Match engine and transmission before checkout.
Confirm mounting ear count and electrical terminal layout.
Plan access first because this job often starts under the vehicle.
Need the walkthrough?
Open starter guide with access notes
Use the full guide when you want location details, wiring order, and removal sequence before going under the vehicle.
No signup required. Loads only when requested for a faster first page view.
Start here with the short guide, then open the full version if you need more detail.
At a glance
The core information most people want before deciding whether to do this repair themselves.
DIY parts cost: $100-300
Difficulty
Intermediate
Time
1-2 hours
Parts
2 items
DIY savings
$100-400+
Safety Warnings
- •Disconnect battery first
- •Starter may be heavy - support before removing bolts
- •Clean mounting surface for good ground
Tools required
Gather these before you start so the job flows cleanly once the vehicle is apart. Click any tool to shop it on Amazon.
Starter fitment and hardware
Starter part numbers often split by engine, transmission, or drive layout. Double-check those before you order.
We surface the most relevant part number, OEM reference, or spec we have for this job so you can compare listings with higher confidence.
Bundle everything
Shop the complete starter replacement kit
Pads, rotors, hardware, fluids, and tools — one search for the whole job.
Highest-risk starter ordering checks
Match the starter first, then confirm bolts or electrical supplies if corrosion is likely.
Starter bolts (if corroded)
Amazon results for 2005 Scion Tc Starter bolts (if corroded)
Open starter fitment →When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
What the Pros Prefer: 2005 Scion Tc Starter Replacement
Professional 4-step job flow, tool sizes, and certified technician best practices.
Job Preparation & Access Clearance
Shop Tip:Clear dust and road grime from the working area before loosening hardware. Protect eyes and hands from fluids and sharp metal edges.
Fastener Extraction & Component Disassembly
Shop Tip:Apply penetrating spray to heat-cycled or rusted bolts 10 minutes prior to removal. Use 6-point sockets to avoid rounding off bolt heads.
Mating Surface Inspection & Cleaning
Shop Tip:Clean all mounting surfaces to bare metal. Verify that old gaskets, O-rings, and crush washers are fully removed before installing new parts.
Final Torque & Operational Verification
Shop Tip:Torque fasteners to factory OEM specifications in an alternating star or criss-cross pattern to ensure uniform clamping pressure.
Affiliate disclosure: As an Amazon Associate, we earn from qualifying purchases on tool links at no extra cost to you.
Basic procedure overview
This is the short version of the job flow. The AI guide below fills in torque specs, access details, and vehicle-specific cautions.
- 1Disconnect battery
- 2Locate starter (usually near transmission)
- 3Remove electrical connections
- 4Remove mounting bolts
- 5Install new starter
- 6Reconnect wiring and battery
Frequently asked questions
- How much does starter replacement cost for a 2005 Scion Tc?
- DIY starter replacement on a 2005 Scion Tc costs approximately $100-300 in parts. A professional shop typically charges $180-500 including labor. By doing it yourself, you save $80–$200+ in labor costs.
- How long does starter replacement take on a 2005 Scion Tc?
- A starter replacement on a 2005 Scion Tc typically takes 1-2 hours for a DIY mechanic. Professional shops may be faster due to lifts and pneumatic tools. First-timers should add 30–60 minutes for setup and learning.
- Can I do starter replacement myself on a 2005 Scion Tc?
- A starter replacement on a 2005 Scion Tc is rated Intermediate. If you have some DIY experience and the right tools, you can do it yourself in about 1-2 hours. First-timers should budget extra time and watch a tutorial first.
- What tools do I need for starter replacement on a 2005 Scion Tc?
- For starter replacement on a 2005 Scion Tc you'll need: Socket wrench set, Extensions, Floor jack, Wire brush. You'll also need the correct replacement parts: Starter motor, Starter bolts (if corroded).
- What happens if I delay starter replacement on my 2005 Scion Tc?
- A failing starter means your 2005 Scion Tc won't start reliably. Continued attempts to start with a bad starter can drain the battery and damage the flywheel ring gear—an expensive transmission-area repair.
- Where is the starter on a 2005 Scion tC?
- On the 2005 Scion tC with the 2.4L 2AZ-FE engine, the starter is mounted on the driver side of the transaxle bellhousing. To reach it, remove the air intake resonator duct and battery hold-down bracket. The upper and lower 14mm mounting bolts are then accessible from above and below the vehicle.
Get the Full AI-Powered Repair Guide
Exact torque specs, part numbers, and step-by-step instructions tailored to your 2005 Scion Tc.
Unlimited AI repair guides for every vehicle. No signup required. Veteran-owned.