Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Signal Specification, Transmission Control Module (TCM)
All the values given below apply between the respective terminal (column 1) and power ground (#A15). If this is not the case, it is indicated within brackets.
- Connector A (28-pin) corresponds to terminals #A1 - #A28 on the breakout box.
- Connector B (33-pin to transmission) corresponds to #B1 - #B33 on the breakout box.
Connect the breakout box and check the ground terminals before taking readings.
| U= | DC voltage in volts (V) | UAC = | AC voltage in volts (V) |
| Ubat = | Battery voltage | F = | Frequency in Hertz (Hz) |
| Ulow = | Voltage approximately 0 V | t = | Time in seconds (s) |
| PWM = | Pulse-width modulation |
| Terminal breakout box | Terminal control module | Signal type | Ignition on | Engine idling | Miscellaneous |
|---|---|---|---|---|---|
| #A1 | #A1 | Power supply | U = Ubat | U = Ubat | 30-feed (KL30) from fuse |
| #A2 | #A2 | Power supply | U = Ubat | U = Ubat | 15-feed (KL15) from ignition via fuse |
| #A3 | #A3 | - | - | - | |
| #A4 | #A4 | - | - | - | |
| #A5 | #A5 | - | - | - | |
| #A6 | #A6 | Electric oil pump control module, control signal. Only hybrid vehicles. |
Duty cycle varies with requested speed on the oil pump. | Pulse width modulation (PWM) signal | |
| #A7 | #A7 | Electric oil pump control module, status signal to Transmission Control Module (TCM). Only hybrid vehicles. |
- | Pulse width modulation (PWM) signal The signal contains the oil pump's status and speed. |
|
| #A8 | #A8 | - | - | - | |
| #A9 | #A9 | - | - | - | |
| #A10 | #A10 | - | - | - | |
| #A11 | #A11 | - | - | - | |
| #A12 | #A12 | - | - | - | |
| #A13 | #A13 | LIN, gear selector module (GSM) | During communication the following applies: U = 0 V - Ubat | - | |
| #A14 | #A14 | - | - | - | |
| #A15 | #A15 | Power ground | U = Ulow | U = Ulow | Ground point |
| #A16 | #A16 | - | - | - | - |
| #A17 | #A17 | - | - | - | - |
| #A18 | #A18 | Start inhibition, signal | U = Ulow when start is permitted | Signal to engine control module (ECM) if start is permitted. | |
| #A19 | #A19 | - | - | - | - |
| #A20 | #A20 | - | - | - | - |
| #A21 | #A21 | - | - | - | - |
| #A22 | #A22 | HS-CAN 1 L | During communication the following applies: U = 1.5 - 2.5 V | Designated in other information "HS-CAN". | |
| #A23 | #A23 | HS-CAN 1 H | During communication the following applies: U = 2.0 - 3.5 V | Designated in other information "HS-CAN". | |
| #A24 | #A24 | HS-CAN 2 L | During communication the following applies: U = 1.5 - 2.5 V | Designated in other information "HS-CAN". | |
| #A25 | #A25 | HS-CAN 2 H | During communication the following applies: U = 2.0 - 3.5 V | Designated in other information "HS-CAN". | |
| #A26 | #A26 | Gear blocking, shift lock solenoid for gear selector module (GSM), signal | Shift lock U = Ubat when the solenoid is not activated U = Ulow when the solenoid is activated |
Inactive solenoid = the gear selector is locked Active solenoid = the gear selector can be moved |
|
| #A27 | #A27 | Gear selector module (GSM), power supply | U = Ubat | U = Ubat | - |
| #A28 | #A28 | - | - | - | - |
| Terminal breakout box | Terminal control module | Signal type | Ignition on | Engine idling | Miscellaneous |
|---|---|---|---|---|---|
| #1 | #B1 | Lock-up solenoid SLU, control signal | PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #2 | #B2 | Lock-up solenoid SLU, signal ground | U = Ulow | U = Ulow | - |
| #3 | #B3 | Linear pressure solenoid SL3, control signal | PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #4 | #B4 | Linear pressure solenoid SL3, signal ground | U = Ulow | U = Ulow | - |
| #5 | #B5 | Linear pressure solenoid SL5, control signal | PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #6 | #B6 | Linear pressure solenoid SLT, control signal | PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #7 | #B7 | Linear pressure solenoid SLT, signal ground | U = Ulow | U = Ulow | - |
| #8 | #B8 | Linear pressure solenoid SL2, control signal | PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #9 | #B9 | Linear pressure solenoid SL2, signal ground | U = Ulow | U = Ulow | - |
| #10 | #B10 | Oil temperature sensor, signal | U=0-5 V | U=0-5 V | Analogue input ("Hall sensor"). |
| #11 | #B11 | Transmission speed sensor (output speed), signal | Tooth against sensor: 14 mA Cover against sensor: 6 mA |
When the toothed wheel rotates, the sensor generates a pulsating current (square wave) with fixed pulse ratio, the frequency increases with the speed. | |
| #12 | #B12 | Linear pressure solenoid SL5, signal ground | U = Ulow | U = Ulow | - |
| #13 | #B13 | Linear pressure solenoid SL1, control signal | PWM (0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #14 | #B14 | Linear pressure solenoid SL1, signal ground | U = Ulow | U = Ulow | - |
| #15 | #B15 | - | - | - | |
| #16 | #B16 | - | - | - | |
| #17 | #B17 | Transmission speed sensor (input speed), signal ground | U = Ulow | U = Ulow | - |
| #18 | #B18 | Transmission speed sensor (input speed), signal | Tooth against sensor: 14 mA Cover against sensor: 6 mA |
When the toothed wheel rotates, the sensor generates a pulsating current (square wave) with fixed pulse ratio, the frequency increases with the speed. | |
| #19 | #B19 | Oil temperature sensor, signal ground | U = Ulow | U = Ulow | - |
| #20 | #B20 | Transmission speed sensor (output speed), signal ground | U = Ulow | U = Ulow | - |
| #21 | #B21 | Linear pressure solenoid SL4, control signal | PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #22 | #B22 | Linear pressure solenoid SL4, signal ground | U = Ulow | U = Ulow | - |
| #23 | #B23 | Gear shift solenoid S1, control signal | Activated: U = 0 - 2 V below Ubat Not activated: Ulow |
The solenoid receives voltage when transmission control module (TCM) activates it during engine braking in 1st gear. | |
| #24 | #B24 | - | - | - | - |
| #25 | #B25 | - | - | - | - |
| #26 | #B26 | - | - | - | - |
| #27 | #B27 | - | - | - | - |
| #28 | #B28 | Gear shift solenoid S2, control signal | Activated: U = 0 - 2 V below Ubat Not activated: Ulow |
The solenoid receives voltage when transmission control module (TCM) activates it during engine braking in 1st gear. | |
| #29 | #B29 | Electromagnetic oil pump EMOP, signal ground. Not present on hybrid vehicles. |
U = Ulow | U = Ulow | - |
| #30 | #B30 | Electromagnetic oil pump EMOP, control signal. Not present on hybrid vehicles. |
PWM (U = 0 - 12 V). The solenoid receives voltage when transmission control module (TCM) activates it. | The frequency is constant (f = 300 Hz) regardless of driving conditions. It is the signal's duty cycle that is modified when the system pressure is adapted. | |
| #31 | #B31 | - | - | - | - |
| #32 | #B32 | - | - | - | - |
| #33 | #B33 | - | - | - | - |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
