2011 Volvo XC90 R-Design, FWDFACTORY OEM SERVICE PROCEDURE

Engine Control Module (ECM) DTCS - B8444S

ENGINE CONTROL MODULE (ECM) - DTC INDEX

OBD-II Code DTC Description
P0011 ECM-P001100 Intake camshaft position control - extended too far - (bank 1). General fault information. Type of fault not specified.
P0012 ECM-P001200 Intake camshaft position control - returned too far - (bank 1). General fault information. Type of fault not specified.
P0014 ECM-P001400 Controlling camshaft position exhaust- too much control- (bank 1). General fault information. No information about fault type
P0015 ECM-P001500 Exhaust camshaft position control - returned too far - (bank 1). General fault information. Type of fault not specified.
P0016 ECM-P001600 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A. General Failure Information. No sub type information
P0017 ECM-P001700 Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor B. General Failure Information. No sub type information
P0018 ECM-P001800 Crankshaft Position - Camshaft Position Correlation - Bank 2 Sensor A. General Failure Information. No sub type information
P0019 ECM-P001900 Crankshaft Position - Camshaft Position Correlation - Bank 2 Sensor B. General Failure Information. No sub type information
P0021 ECM-P002100 Intake camshaft position control - extended too far - (bank 2). General fault information. Type of fault not specified.
P0022 ECM-P002200 Intake camshaft position control - returned too far - (bank 2). General fault information. Type of fault not specified.
P0024 ECM-P002400 Controlling camshaft position exhaust - too much control- (bank 2). General fault information. No information about fault type
P0025 ECM-P002500 Exhaust camshaft position control - returned too far - (bank 2). General fault information. Type of fault not specified.
P0031 ECM-P003100 Heated oxygen sensor (HO2S) control circuit low (bank 1, sensor 1). General fault information. No information about fault type
P0032 ECM-P003200 Heated oxygen sensor (HO2S) control circuit high (bank 1, sensor 1). General fault information. No information about fault type
P0036 ECM-P003600 HO2S Heater Control Circuit (Bank 1, Sensor 2). General Failure Information. No sub type information
P0037 ECM-P003700 Heated oxygen sensor (HO2S) control circuit low (bank 1, sensor 2). General fault information. No information about fault type
P0038 ECM-P003800 Heated oxygen sensor (HO2S) control circuit high (bank 1, sensor 2). General fault information. No information about fault type
P0051 ECM-P005100 Heated oxygen sensor (HO2S) control circuit low (bank 2, sensor 1). General fault information. No information about fault type
P0052 ECM-P005200 Heated oxygen sensor (HO2S) control circuit high (bank 2, sensor 1). General fault information. No information about fault type
P0057 ECM-P005700 Heated oxygen sensor (HO2S) control circuit low (bank 2, sensor 2). General fault information. No information about fault type
P0058 ECM-P005800 Heated oxygen sensor (HO2S) control circuit high (bank 2, sensor 2). General fault information. No information about fault type
P0071 ECM-P007100 Ambient Air Temperature Sensor Range/Performance. General Failure Information. No sub type information
P0072 ECM-P007200 Ambient air temperature sensor circuit low input signal. General fault information. Type of fault not specified.
P0073 ECM-P007300 Ambient air temperature sensor circuit high input signal. General fault information. Type of fault not specified.
P0075 ECM-P007500 Intake valve control circuit (bank 1). General fault information. Type of fault not specified.
P0076 ECM-P007600 Intake valve control circuit low (bank 1). General fault information. Type of fault not specified.
P0077 ECM-P007700 Intake valve control circuit high (bank 1). General fault information. Type of fault not specified.
P0078 ECM-P007800 Exhaust valve control circuit (bank 1). General fault information. Type of fault not specified.
P0079 ECM-P007900 Exhaust valve control circuit low (bank 1). General fault information. Type of fault not specified.
P0080 ECM-P008000 Exhaust valve control circuit high (bank 1). General fault information. Type of fault not specified.
P0089 ECM-P008900 Fuel pressure regulator performance. General fault information. No information about fault type
P0091 ECM-P009100 Fuel pressure regulator control circuit low. General fault information. Type of fault not specified.
P0092 ECM-P009200 Fuel pressure regulator control circuit high. General fault information. Type of fault not specified.
P009A ECM-P009A21 Intake Air Temperature /Ambient Air Temperature Correlation. General Signal Failures. Signal too low
P0101 ECM-P010100 Air mass or volume air flow circuit within/exceeding limit values. General fault information. Type of fault not specified.
P0102 ECM-P010200 Air mass or volume, airflow circuit low input signal. General fault information. Type of fault not specified.
P0103 ECM-P010300 Air mass or volume, airflow circuit high input signal. General fault information. Type of fault not specified.
P0106 ECM-P010600 Manifold Absolute Pressure/BARO Sensor Range/Performance. General Failure Information. No sub type information
P0107 ECM-P010700 Manifold absolute pressure/BARO sensor low input. General fault information. Type of fault not specified.
P0108 ECM-P010800 Manifold absolute pressure/BARO sensor high input. General fault information. Type of fault not specified.
P0111 ECM-P011100 Intake air temperature sensor 1 circuit within/exceeding limit values. General fault information. Type of fault not specified.
P0112 ECM-P011200 Intake air temperature sensor 1 circuit low input signal. General fault information. Type of fault not specified.
P0113 ECM-P011300 Intake air temperature sensor 1 circuit high input signal. General fault information. Type of fault not specified.
P0114 ECM-P011400 Intake air temperature sensor 1 intermittent/irregular. General fault information. Type of fault not specified.
P0116 ECM-P011600 Coolant temperature circuit within/outside the range. General fault information. No information about fault type
P0116 ECM-P011629 Engine Coolant Temperature Sensor 1 Circuit Range/Performance. General Signal Failures. Signal signal invalid
P0117 ECM-P011700 Coolant temperature circuit low input signal. General fault information. No information about fault type
P0118 ECM-P011800 Coolant temperature circuit high input signal. General fault information. No information about fault type
P0122 ECM-P012200 Throttle/pedal position sensor A circuit low input signal. General fault information. No information about fault type.
P0123 ECM-P012300 Throttle/pedal position sensor A circuit high input signal. General fault information. No information about fault type.
P0128 ECM-P012800 Coolant thermostat (coolant temperature lower than thermostat-control temperature. General malfunction information. No information on malfunction type
P0131 ECM-P013100 O2 Circuit Low Voltage (Bank 1, Sensor 1). General Failure Information. No sub type information
P0132 ECM-P013200 O2 Circuit High Voltage (Bank 1, Sensor 1). General Failure Information. No sub type information
P0133 ECM-P013300 Heated oxygen sensor (HO2S) slow response (bank 1, sensor 1). General fault information. No information about fault type
P0134 ECM-P013400 Heated oxygen sensor (HO2S) circuit no activity registered (bank 1, sensor 1). General fault information. No information about fault type
P0136 ECM-P013600 Heated oxygen sensor (HO2S) circuit (bank 1, sensor 2). General fault information. No information about fault type
P0137 ECM-P013700 Heated oxygen sensor (HO2S) circuit low voltage (bank 1, sensor 2). General fault information. No information about fault type
P0138 ECM-P013800 Heated oxygen sensor (HO2S) circuit high voltage (bank 1, sensor 2). General fault information. No information about fault type
P013A ECM-P013A00 O2 Sensor Slow Response - Rich to Lean (Bank 1 and Sensor 2). General Failure Information. No sub type information
P013C ECM-P013C00 O2 Sensor Slow Response - Rich to Lean (Bank 2, Sensor 2). General Failure Information. No sub type information
P0151 ECM-P015100 O2 Circuit Low Voltage (Bank 2, Sensor 1). General Failure Information. No sub type information
P0152 ECM-P015200 O2 Circuit High Voltage (Bank 2, Sensor 1). General Failure Information. No sub type information
P0153 ECM-P015300 Heated oxygen sensor (HO2S) slow response (bank 2, sensor 1). General fault information. No information about fault type
P0154 ECM-P015400 Heated oxygen sensor (HO2S) circuit no activity registered (bank 2, sensor 1). General fault information. No information about fault type
P0156 ECM-P015600 Heated oxygen sensor (HO2S) circuit (bank 2, sensor 2). General fault information. No information about fault type
P0157 ECM-P015700 Heated oxygen sensor (HO2S) circuit low voltage (bank 2, sensor 2). General fault information. No information about fault type
P0158 ECM-P015800 Heated oxygen sensor circuit high voltage (bank 2, sensor 2). General malfunction information. No information on malfunction type
P0171 ECM-P017100 System too lean (bank 1). General malfunction information. No information on malfunction type
P0172 ECM-P017200 System too rich (bank 1). General malfunction information. No information on malfunction type
P0174 ECM-P017400 System too lean (bank 2). General malfunction information. No information on malfunction type
P0175 ECM-P017500 System too rich (bank 2). General malfunction information. No information on malfunction type
P0181 ECM-P018100 Fuel pressure temperature sensor A circuit within/outside range. General fault information. No information about fault type
P0182 ECM-P018200 Fuel temperature sensor A circuit low input signal. General fault information. No information about fault type
P0183 ECM-P018300 Fuel temperature sensor A circuit high input signal. General fault information. No information about fault type
P0191 ECM-P019100 Fuel rail pressure sensor within/outside limit values. General fault information. No information about fault type
P0192 ECM-P019200 Fuel rail pressure sensor low input. General fault information. No information about fault type
P0193 ECM-P019300 Fuel rail pressure sensor high input. General fault information. No information about fault type
P0201 ECM-P020100 Injector cylinder 1 open-circuit. General fault information. Type of fault not specified.
P0221 ECM-P022100 Throttle/pedal position switch B circuit within/outside range. General fault information. No information about fault type.
P0222 ECM-P022200 Throttle/pedal position sensor B circuit low input signal. General fault information. No information about fault type.
P0223 ECM-P022300 Throttle/pedal position sensor B circuit high input signal. General fault information. No information about fault type
P0300 ECM-P030000 Random misfire registered. General fault information. Type of fault not specified.
P0301 ECM-P030100 Cylinder 1 misfire registered. General fault information. Type of fault not specified.
P0326 ECM-P032600 Knock sensor 1 circuit within/exceeding limit values (bank 1). General fault information. Type of fault not specified.
P0327 ECM-P032700 Knock sensor 1 circuit low input signal (bank 1). General fault information. Type of fault not specified.
P0328 ECM-P032800 Knock sensor 1 circuit high input signal (bank 1). General fault information. Type of fault not specified.
P0331 ECM-P033100 Knock sensor 2 circuit within/exceeding limit values (bank 2). General fault information. Type of fault not specified.
P0332 ECM-P033200 Knock sensor 2 circuit low input signal (bank 2). General fault information. Type of fault not specified.
P0333 ECM-P033300 Knock sensor 2 circuit high input signal (bank 2). General fault information. Type of fault not specified.
P0335 ECM-P033500 Crankshaft position sensor A circuit low input signal. General fault information. Type of fault not specified.
P0336 ECM-P033600 Crankshaft position sensor A circuit within/exceeding limit values. General fault information. Type of fault not specified.
P0339 ECM-P033900 Crankshaft position sensor A circuit intermittent. General fault information. Type of fault not specified.
P0340 ECM-P034000 Camshaft Position Sensor A Circuit (Bank 1 or single sensor). General Failure Information. No sub type information
P0341 ECM-P034100 Camshaft position sensor A circuit within/exceeding limit values (bank 1 or single sensor). General fault information. Type of fault not specified.
P0345 ECM-P034500 Camshaft Position Sensor A Circuit (Bank 2). General Failure Information. No sub type information
P0346 ECM-P034600 Camshaft position sensor A circuit within/exceeding limit values (bank 2). General fault information. Type of fault not specified.
P0351 ECM-P035100 Ignition coil A, primary/secondary circuit. General fault information. Type of fault not specified.
P0365 ECM-P036500 Camshaft Position Sensor B Circuit (Bank 1). General Failure Information. No sub type information
P0366 ECM-P036600 Camshaft Position Sensor B Circuit Range/Performance (Bank 1). General Failure Information. No sub type information
P0369 ECM-P039000 Camshaft Position Sensor B Circuit (Bank 2). General Failure Information. No sub type information
P0391 ECM-P039100 Camshaft Position Sensor B Circuit Range/Performance (Bank 2). General Failure Information. No sub type information
P0420 ECM-P042000 Catalyst System Efficiency Below Threshold (Bank 1). General Failure Information. No sub type information
P0430 ECM-P043000 Catalyst System Efficiency Below Threshold (Bank 2). General Failure Information. No sub type information
P043E ECM-P043E00 Evaporative Emission System Leak Detection Reference Orifice Low Flow. General Failure Information. No sub type information
P0441 ECM-P044100 EVAP emission system, faulty purge flow. General fault information. Type of fault not specified.
P0442 ECM-P044200 Evaporative Emission System Leak Detected (small leak). General Failure Information. No sub type information
P0455 ECM-P045500 EVAP emission system leakage registered (large leak/no flow). General fault information. Type of fault not specified.
P0458 ECM-P045800 EVAP emission system purge control valve circuit low. General fault information. Type of fault not specified.
P0459 ECM-P045900 EVAP emission system purge control valve circuit high. General fault information. Type of fault not specified.
P0461 ECM-P046100 Fuel level sensor A circuit within/outside limit values. General malfunction information. No information on malfunction type
P0462 ECM-P046200 Fuel level sensor A circuit low input signal. General malfunction information. No information on malfunction type
P0464 ECM-P046400 Fuel level sensor A circuit intermittent. General malfunction information. No information on malfunction type
P0480 ECM-P048000 Fan 1 control circuit. General fault information. Type of fault not specified.
P0500 ECM-P050000 Speed sensor A. General malfunction information. No information on malfunction type
P0501 ECM-P050100 Speed sensor A within/outside limit values. General malfunction information. No information on malfunction type
P0506 ECM-P050600 Idle control rpm lower than expected. General malfunction information. No information on malfunction type
P0507 ECM-P050700 Idle control rpm higher than expected. General malfunction information. No information on malfunction type
P050A ECM-P050A00 Cold Start Idle Air Control System Performance. General Failure Information. No sub type information
P050B ECM-P050B00 Cold Start Ignition Timing Performance. General Failure Information. No sub type information
P0512 ECM-P051200 Start request circuit. General fault information. Type of fault not specified.
P052A ECM-P052A00 Cold Start Camshaft Position Timing Over-Advanced (Bank 1). General Failure Information. No sub type information
P052B ECM-P052B00 Cold Start Camshaft Position Timing Over-Retarded (Bank 1). General Failure Information. No sub type information
P052C ECM-P052C00 Cold Start Camshaft Position Timing Over-Advanced (Bank 2). General Failure Information. No sub type information
P052D ECM-P052D00 Cold Start Camshaft Position Timing Over-Retarded (Bank 2). General Failure Information. No sub type information
P0531 ECM-P053100 A/C refrigerant pressure sensor A circuit within/outside limit values. General malfunction information. No information on malfunction type
P0532 ECM-P053200 A/C refrigerant pressure sensor A circuit low input signal. General malfunction information. No information on malfunction type
P0533 ECM-P053300 A/C refrigerant pressure sensor A circuit high input signal. General malfunction information. No information on malfunction type
P0534 ECM-P053400 A/C refrigerant charging loss. General malfunction information. No information on malfunction type
P054A ECM-P054A00 Cold Start Exhaust (B) Camshaft Position Timing Over-Advanced (Bank 1). General Failure Information. No sub type information
P054B ECM-P054B00 Cold Start Exhaust (B) Camshaft Position Timing Over-Retarded (Bank 1). General Failure Information. No sub type information
P054C ECM-P054C00 Cold Start Exhaust (B) Camshaft Position Timing Over-Advanced (Bank 2). General Failure Information. No sub type information
P054D ECM-P054D00 Cold Start Exhaust (B) Camshaft Position Timing Over-Retarded (Bank 2). General Failure Information. No sub type information
P0562 ECM-P056200 System voltage low. General malfunction information. No information on malfunction type
P0563 ECM-P056300 System voltage high. General malfunction information. No information on malfunction type
P0574 ECM-P057400 Cruise Control System - Vehicle Speed Too High. General Failure Information. No sub type information
P0603 ECM-P060300 Internal malfunction in control module (KAM). General malfunction information. No information on malfunction type
P0607 ECM-P060700 Control module performance. General fault information. No information about fault type
P0615 ECM-P061500 Starter relay circuit. General fault information. Type of fault not specified.
P0616 ECM-P061600 Starter relay circuit low. General fault information. Type of fault not specified.
P0617 ECM-P061700 Starter relay circuit high. General fault information. Type of fault not specified.
P061A ECM-P061A62 Internal Control Module Torque Performance. Algorithm Based Failures. Signal compare failure
P0620 ECM-P062001 Generator Control Circuit. General Failure Information. General electrical failure
P0620 ECM-P06204B Generator Control Circuit. System Internal Failures. Over temperature
P0620 ECM-P062074 Generator Control Circuit. Mechanical Failures. Actuator slipping
P0628 ECM-P062800 Fuel pump A control circuit low. General fault information. No information about fault type
P0629 ECM-P062900 Fuel pump A control circuit high. General fault information. No information about fault type
P0634 ECM-P063400 PCM/ECM/TCM Internal temperature too high. General malfunction information. No information on malfunction type
P0641 ECM-P064100 Sensor reference voltage A open circuit. General malfunction information. No information on malfunction type
P0645 ECM-P064500 A/C connection relay control circuit. General malfunction information. No information on malfunction type
P0646 ECM-P064600 A/C connection relay control circuit low. General malfunction information. No information on malfunction type
P0647 ECM-P064700 A/C connection relay control circuit high. General malfunction information. No information on malfunction type
P0661 ECM-P066100 Intake manifold control valve control circuit low - bank 1. General fault information. No information about fault type
P0662 ECM-P066200 Intake manifold control valve control circuit high - bank 1. General fault information. No information about fault type
P0668 ECM-P066800 PCM/ECM/TCM internal temperature sensor circuit low. General malfunction information. No information on malfunction type
P0685 ECM-P068500 ECM/PCM power relay control circuit/open circuit. General malfunction information. No information on malfunction type
P0691 ECM-P069100 Fan 1 control circuit low. General fault information. Type of fault not specified.
P0692 ECM-P069200 Fan 1 control circuit high. General fault information. Type of fault not specified.
P0737 ECM-P073700 TCM engine rpm output circuit. General malfunction information. No information on malfunction type
P1126 ECM-P112600 Throttle Position (Narrow Range) Sensor Circuit. General Failure Information. No sub type information
P1224 ECM-P122400 Throttle Position Sensor B Out Of Self Test Range. General Failure Information. No sub type information
P1250 ECM-P125000 Throttle Valve Spring. General Failure Information. No sub type information
P1260 ECM-P126000 Theft registered, vehicle immobilized. General malfunction information. No information on malfunction type
P1270 ECM-P127000 Engine rpm or speed limitation reached. General malfunction information. No information on malfunction type
P1572 ECM-P157200 Bake pedal switch circuit. General fault information. Type of fault not specified.
P1574 ECM-P157400 Throttle position sensor output signals are not correct. General malfunction information. No information on malfunction type
P1589 ECM-P158900 Throttle Control Unable To Control To Desired Throttle Angle. General Failure Information. No sub type information
P1602 ECM-P160200 Immobilizer/ECM communication error. General malfunction information. No information on malfunction type
P1638 ECM-P163800 CAN-link ECM/INSTM circuit/network. General malfunction information. No information on malfunction type
P1709 ECM-P170900 Parking/neutral position switch outside self-test range. General malfunction information. No information on malfunction type
P1771 ECM-P177100 Throttle Position Sensor Circuit High Input. General Failure Information. No sub type information
P1772 ECM-P177200 Electronic throttle unit low input signal. General malfunction information. No information on malfunction type
P1934 ECM-P193400 Speed signal vehicle. General malfunction information. No information on malfunction type
P2004 ECM-P200400 Intake Manifold Runner Control Stuck Open (Bank 1). General Failure Information. No sub type information
P2006 ECM-P200600 Variable intake stuck in closed position (bank 1). General fault information. No information about fault type
P2067 ECM-P206700 Fuel level sensor B circuit low. General malfunction information. No information on malfunction type
P2096 ECM-P209600 Post Catalyst Fuel Trim System Too Lean Bank 1. General Failure Information. No sub type information
P2106 ECM-P210600 Throttle Actuator Control System - Forced Limited Power. General Failure Information. No sub type information
P2111 ECM-P211100 Electronic throttle unit control system - jammed in open position. General malfunction information. No information on malfunction type
P2118 ECM-P211800 Throttle Actuator Control Motor Current Range/Performance. General Failure Information. No sub type information
P2135 ECM-P213500 Throttle/pedal position sensor/contact A/B voltage correlation. General fault information. Type of fault not specified.
P2158 ECM-P215886 Vehicle Speed Sensor B. Bus Signal / Message Failures. Signal invalid
P2162 ECM-P216200 Speed sensor A/B correlation. General malfunction information. No information on malfunction type
P2175 ECM-P217500 Electronic throttle unit control system - low air flow registered. General malfunction information. No information on malfunction type
P2227 ECM-P222700 Barometric Pressure Circuit High Input. General Failure Information. No sub type information
P2228 ECM-P222800 Atmospheric pressure circuit low input signal. General fault information. Type of fault not specified.
P2270 ECM-P227000 O2 Sensor Signal Stuck Lean - Bank 1, Sensor 2. General Failure Information. No sub type information
P2271 ECM-P227100 O2 Sensor Signal Stuck Rich - Bank 1, Sensor 2. General Failure Information. No sub type information
P2272 ECM-P227200 O2 Sensor Signal Stuck Lean - Bank 2, Sensor 2. General Failure Information. No sub type information
P2273 ECM-P227300 O2 Sensor Signal Stuck Rich - Bank 2, Sensor 2. General Failure Information. No sub type information
P2401 ECM-P240100 EVAP emission system, leakage diagnosis pump control circuit low. General fault information. Type of fault not specified.
P2402 ECM-P240200 EVAP emission system, leakage diagnosis pump control circuit high. General fault information. Type of fault not specified.
P2408 ECM-P240800 Tank cap sensor/contact circuit. General fault information. Type of fault not specified.
P240B ECM-P240B00 EVAP emission system, leakage diagnosis pump heating circuit low. General fault information. Type of fault not specified.
P240C ECM-P240C00 EVAP emission system, leakage diagnosis pump heating circuit high. General fault information. Type of fault not specified.
P2419 ECM-P241900 Tank ventilation system changeover valve control circuit low. General fault information. Type of fault not specified.
P2420 ECM-P242000 Tank ventilation system changeover valve control circuit low. General fault information. Type of fault not specified.
P2421 ECM-P242100 Evaporative Emission Control System Vent Valve Stuck Open. General Failure Information. No sub type information
P2422 ECM-P242200 Evaporative Emission Control System Vent Valve Stuck Closed. General Failure Information. No sub type information
P250C ECM-P250C00 Oil level sensor circuit low. General fault information. Type of fault not specified.
P250D ECM-P250D00 Oil level sensor circuit high. General fault information. Type of fault not specified.
P250E ECM-P250E00 Oil level sensor circuit intermittent/irregular. General fault information. Type of fault not specified.
P252B ECM-P252B00 Oil quality sensor circuit within/exceeding limit values. General fault information. Type of fault not specified.
P252C ECM-P252C00 Oil quality sensor circuit low. General fault information. Type of fault not specified.
P252D ECM-P252D00 Oil quality sensor circuit high. General fault information. Type of fault not specified.
P2610 ECM-P261000 ECM/PCM internal engine shut-down timer performance. General malfunction information. No information on malfunction type
U0001 ECM-U000100 HS-CAN communication bus. General malfunction information. No information on malfunction type
U0101 ECM-U010100 Failed communication with transmission control module. General malfunction information. No information on malfunction type
U0104 ECM-U010400 Failed communication with cruise control module. General fault information. Type of fault not specified.
U0107 ECM-U010700 Lost Communication With Throttle Actuator Control Module. General Failure Information. No sub type information
U0120 ECM-U012086 Lost Communication with Starter/ Generator Control Module. Bus Signal / Message Failures. Signal invalid
U0120 ECM-U012087 Lost Communication with Starter/ Generator Control Module. Bus Signal / Message Failures. Missing message
U0121 ECM-U012100 Failed communication with brake control module. General malfunction information. No information on malfunction type
U0129 ECM-U012900 Failed communication with brake control module (BCM). General fault information. Type of fault not specified.
U0141 ECM-U014100 Failed communication with central electronic module "A". General malfunction information. No information on malfunction type
U0322 ECM-U032200 Software incompatible with body control module. General malfunction information. No information on malfunction type
U0400 ECM-U040000 Invalid data received. General malfunction information. No information on malfunction type
U0405 ECM-U040500 Invalid data from cruise control module. General fault information. Type of fault not specified.
U0418 ECM-U041823 Invalid Data Received From Brake control module. General Signal Failures. Signal stuck low
U0422 ECM-U042200 Invalid data received from central electronic module. General malfunction information. No information on malfunction type
U0426 ECM-U042600 Invalid data received from vehicle immobilizer control module. General malfunction information. No information on malfunction type
NA ECM-XXXXXX Unknown diagnostic trouble code (DTC) for current control module version
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.