Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2011 Volvo S40 T-5 R-DesignFACTORY OEM SERVICE PROCEDURE
Conversion Table Standardized Diagnostic Trouble Codes (DTCS)/VOLVO Diagnostic Trouble Codes (DTCS): Table
| SAE/ISO diagnostic trouble code (DTC) | Volvo DII diagnostic trouble code (DTC) | Diagnostic trouble code (DTC) designation | Fault type |
| P0218 | TCM-0046 | Oil temperature sensor | Temperature too high |
| P0560 P0561 |
TCM-009A | Battery voltage | Signal too low |
| P0560 | TCM-009B | Battery voltage | Faulty voltage |
| P0600 P1934 |
TCM-0A01 | Control module communication | Signal missing |
| P0600 P0725 |
TCM-0A30 | Control module communication | No signal from ECM |
| P0600 P1719 |
TCM-0A31 | Control module communication | No signal from ECM |
| P0614 | TCM-0048 | Control module | Faulty software |
| P0601 | TCM-0049 | Transmission control module (TCM) | Internal fault |
| P0605 P062F |
TCM-0099 | Transmission control module (TCM) | Internal fault |
| P0605 | TCM-029A | Transmission control module (TCM) | Internal fault |
| P0610 | TCM-0048 | Transmission control module (TCM) | Faulty software |
| P0610 | TCM-E003 | Control module communication | Faulty configuration |
| P0705 | TCM-0039 | Gear-shift position sensor | Faulty signal |
| P0705 P0708 |
TCM-0286 | Hall sensor in the gear selector | Internal fault |
| P0705 P0707 |
TCM-0287 | Hall sensor in the gear selector | Internal fault |
| P0705 P0708 |
TCM-0291 | Hall sensor in the gear selector | Internal fault |
| P0705 P0707 |
TCM-0292 | Hall sensor in the gear selector | Internal fault |
| P0715 | TCM-0087 | Transmission input speed sensor | Signal missing |
| P0715 P0718 |
TCM-0088 | Transmission input speed sensor | Signal missing |
| P0717 | TCM-0022 | Transmission input speed sensor | Signal missing |
| P0717 | TCM-0023 | Transmission input speed sensor | Signal missing |
| P0716 | TCM-0024 | Transmission input speed sensor | Faulty signal |
| P0720 P0502 |
TCM-0081 | Transmission output speed sensor | Signal missing |
| P0720 P0503 |
TCM-0082 | Transmission output speed sensor | Signal missing |
| P0721 P0501 |
TCM-0020 | Transmission output speed sensor | Faulty signal |
| P0722 P0500 |
TCM-001E | Transmission output speed sensor | Signal missing |
| P0722 P0500 |
TCM-001F | Transmission output speed sensor | Faulty signal |
| P0731 | TCM-0028 | Gear 1 | Incorrect gear ratio |
| P0732 | TCM-0029 | Gear 2 | Incorrect gear ratio |
| P0733 | TCM-002A | Gear 3 | Incorrect gear ratio |
| P0734 | TCM-002B | Gear 4 | Incorrect gear ratio |
| P0735 | TCM-002C | Gear 5 | Incorrect gear ratio |
| P0736 | TCM-0027 | Back-up gear | Incorrect gear ratio |
| P0741 P0811 |
TCM-002F | Lock-up function | Slips or does not engage |
| P0748 P0960 |
TCM-0117 | Linear pressure solenoid SLT | Signal missing |
| P0748 P0963 |
TCM-0124 | Linear pressure solenoid SLT | Faulty signal |
| P0753 P0974 |
TCM-0002 | Shift solenoid S1 | Signal missing |
| P0753 P0973 |
TCM-0003 | Shift solenoid S1 | Signal too low |
| P0758 P0977 |
TCM-0008 | Shift solenoid S2 | Signal missing |
| P0758 P0976 |
TCM-0009 | Shift solenoid S2 | Signal too low |
| P0762 | TCM-0212 | Shift solenoid S3 | Hydraulic fault |
| P0763 P0980 |
TCM-0102 | Shift solenoid S3 | Signal missing |
| P0763 P0979 |
TCM-0103 | Shift solenoid S3 | Signal too low |
| P0768 | TCM-0107 | Shift solenoid S4 | Signal too high |
| P0768 P0983 |
TCM-0108 | Shift solenoid S4 | Signal missing |
| P0768 P0982 |
TCM-0109 | Shift solenoid S4 | Signal too low |
| P0773 P0986 |
TCM-010B | Shift solenoid S5 | Signal missing |
| P0773 P0985 |
TCM-010C | Shift solenoid S5 | Signal too low |
| P0778 P0964 |
TCM-010F | Lock-up solenoid SLU | Signal missing |
| P0778 P0967 |
TCM-0123 | Lock-up solenoid SLU | Faulty signal |
| P0780 | TCM-0100 | Transmission | Poor gear shifting quality |
| P0798 P0968 |
TCM-0113 | Line pressure solenoid SLS | Signal missing |
| P0798 P0971 |
TCM-0122 | Line pressure solenoid SLS | Faulty signal |
| P0817 P081B |
TCM-0070 | Function, start inhibitor | Signal missing |
| P0817 | TCM-0071 | Function, start inhibitor | Faulty signal |
| P0826 | TCM-0096 | Gear selector module (GSM) | Signal missing |
| P0860 | TCM-019B | Gear selector module (GSM) | Signal too low |
| P0860 | TCM-DD00 | Control module communication | Communication fault |
| P0860 | TCM-DD01 | Control module communication | Communication fault |
| P0860 | TCM-DD02 | Control module communication | Communication fault |
| P0860 | TCM-DD10 | Control module communication | Communication fault |
| P0863 | TCM-E000 | Control module communication | Control module communication |
| P0885 | TCM-019C | Gear selector module (GSM) | Signal missing |
| P0928 | TCM-0076 | Function, shift lock | Faulty signal |
| P0928 | TCM-0091 | Park/neutral position shift lock solenoid | Signal missing |
| P0930 | TCM-0092 | Park/neutral position shift lock solenoid | Signal too low |
| P0931 | TCM-0075 | Function, shift lock | Signal missing |
| P0938 | TCM-0045 | Oil temperature sensor | Faulty signal |
| P0939 | TCM-0043 | Oil temperature sensor | Temperature too high |
| P0940 | TCM-0044 | Oil temperature sensor | Temperature too high |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
