2009 Volvo XC90 R-Design, AWDFACTORY OEM SERVICE PROCEDURE

Signal Specification, CARPHONE

General 

All the values given below are between the respective connection in column 1 and connection #A6 in column 2 (power ground) unless otherwise stated in brackets.

NOTE:

It is important to connect the breakout box and check the ground terminals before taking readings.

For information on:

There may be several connections and connectors between control modules and components.

U= DC voltage in volts (V) UAC = AC voltage in volts (V)
Ubat = Battery voltage (V) f = Frequency in Hertz (Hz)
Ulow = Voltage approx. 0 V t = Time in s (seconds)
PWM = Pulse-width modulated signal in %    
Fig 1: Identifying Connector (F) Terminals
GLL104034Courtesy of VOLVO CARS CORPORATION
SIGNAL TABLE CONNECTOR A, PHONE MODULE (PHM)

Connection 
breakout box 
Connection 
control module 
Signal type  Ignition on  Idle  Other 
#1 #A1 - - - -
#2 #A2 - - - -
#3 #A3 - - - -
#4 #A4 - - - -
#5 #A5 +30-feed Ubat Ubat -
#6 #A6 Power ground Ulow Ulow -
#7 #A7 Handset, voltage feed Ubat Ubat -
#8 #A8 Handset, cradle signal U=5 V when handset is used, otherwise U=0 V. U=5 V when handset is used, otherwise U=0 V. -
#9 #A9 - - - -
#10 #A10 - - - -
#11 #A11 CAN (L) Digital signal Digital signal -
#12 #A12 CAN (H) Digital signal Digital signal -
#13 #A13 - - - -l
#14 #A14 - - - -
#15 #A15 - - - -
#16 #A16 - - - -
#17 #A17 Impact cable from SRS U=12 V at activated SRS-component, otherwise U=0 V U=12 V at activated SRS-component, otherwise U=0 V -
#18 #A18 Handset, ground Ulow Ulow -
#19 #A19 Handset, microphone Alternating voltage at sound in microphone Alternating voltage at sound in microphone Difficult to measure
#20 #A20 Handset, speaker Alternating voltage at sound in speaker Alternating voltage at sound in speaker Difficult to measure
#21 #A21 - - - -
#22 #A22 - - - -
Fig 2: Identifying Signal Table Connector B, Phone Module (PHM)
GLL101505Courtesy of VOLVO CARS CORPORATION
SIGNAL TABLE CONNECTOR B, PHONE MODULE (PHM)

Connection 
breakout box 
Connection 
control module 
Signal type  Ignition on  Idle  Other 
#21 #B1 Clock signal to SIM-card Pound signal Pound signal -
#22 #B2 Signal ground, SIM-card Ulow Ulow -
#23 #B3 Voltage feed, SIM-card U=2.8 V U=2.8 V -
#24 #B4 Communication cable, SIM-card Pulsed signal Pulsed signal -
#25 #B5 Control signal, SIM-card Pulsed signal Pulsed signal -
#26 #B6 Diagnostic cable, SIM-card Ulow Ulow -
Fig 3: Identifying 1-Bit Connector
GLL139873Courtesy of VOLVO CARS CORPORATION
SIGNAL TABLE CONNECTOR C, PHONE MODULE (PHM)

Connection 
breakout box 
Connection 
control module 
Signal type  Ignition on  Idle  Other 
- #C1 Telephone antenna Antenna signal telephone Antenna signal telephone -
- #C2 Antenna ground Ulow Ulow -
Fig 4: Identifying Connector C
GLL108086Courtesy of VOLVO CARS CORPORATION
SIGNAL TABLE CONNECTOR D, PHONE MODULE (PHM)

Connection 
breakout box 
Connection 
control module 
Signal type  Ignition on  Idle  Other 
- #D1 MOST input signal Optical input signal when the MOST network is activated Optical input signal when the MOST network is activated -
- #D2 MOST output signal Optical output signal when the MOST network is activated Optical output signal when the MOST network is activated -
Fig 5: Identifying Signal Table Connector B, Phone Module (PHM)
GLL101505Courtesy of VOLVO CARS CORPORATION
SIGNAL TABLE CONNECTOR SIM-CARD HOLDER

Connection 
breakout box 
Connection 
control module 
Signal type  Ignition on  Idle  Other 
#21 #1 Clock signal to SIM-card Pound signal Pound signal -
#22 #2 Signal ground, SIM-card Ulow Ulow -
#23 #3 Voltage feed, SIM-card U=2.8 V U=2.8 V -
#24 #4 Communication cable, SIM-card Pulsed signal Pulsed signal -
#25 #5 Control signal, SIM-card Pulsed signal Pulsed signal -
#26 #6 Diagnostic cable, SIM-card Ulow Ulow -
Fig 6: 10 CD Changer Connector Terminals
GLL104029Courtesy of VOLVO CARS CORPORATION
SIGNAL TABLE CONNECTOR HANDSET

Connection 
breakout box 
Connection 
control module 
Signal type  Ignition on  Idle  Other 
#21 #1 Handset, microphone Alternating voltage at sound in microphone Alternating voltage at sound in microphone Difficult to measure
#22 #2 Handset, speaker Alternating voltage at sound in microphone Alternating voltage at sound in microphone Difficult to measure
#23 #3 Handset, ground Ulow Ulow -
#24 #4 Handset, cradle signal U=5 V when handset is used, otherwise U=0 V. U=5 V when handset is used, otherwise U=0 V. -
#25 #5 Handset, voltage feed Ubat Ubat -
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.