Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Volvo S80 BaseFACTORY OEM SERVICE PROCEDURE
Signal Specification
GeneralÂ
All the values given below are between the terminals stated in column 1 and terminal #C2:4 in column 2 (power ground).
NOTE:
It is important to connect the breakout box and check the ground terminals before taking readings.
| U= | DC voltage in volts (V) | UAC = | AC voltage in volts (V) |
| Ubat = | Battery voltage (V) | f = | Frequency in Hertz (Hz) |
| Ulow = | Voltage approximately 0 V | t = | Time in seconds |
| PWM = | Pulse width modulated signal as a % | Â | Â |
CONNECTOR C1
| Breakout box terminal | Control module terminal | Signal type | Ignition off | Ignition on | Other |
|---|---|---|---|---|---|
| #31 | #C1:1 | - | - | - | - |
| #32 | #C1:2 | Power supply, trailer module (TRM), 30-supply | U = Ubat | U = Ubat | - |
CONNECTOR C2
| Breakout box terminal | Control module terminal | Signal type | Ignition off | Ignition on | Other |
|---|---|---|---|---|---|
| #22 | #C2:1 | CAN H | U = Ulow | During communication U = 2.5 - 4.0 V | - |
| #23 | #C2:2 | CAN L | U = Ulow | During communication U = 1.0 - 2.5 V | - |
| #24 | #C2:3 | Stop lamp, input signal | During activation U = Ubat | During activation U = Ubat | From the central electronic module (CEM) via the vehicle's left-hand tail lamp. |
| #25 | #C2:4 | Ground | Ulow | Ulow | - |
| #26 | #C2:5 | - | - | - | - |
CONNECTOR C3
| Breakout box terminal | Control module terminal | Signal type | Ignition off | Ignition on | Other |
|---|---|---|---|---|---|
| - | #C3:1 | Right turn signal lamp | U = Ulow | During activation and normal function f = 1, 5Hz, PWM = 50 % | - |
| - | #C3:2 | Charging (+12 V) (Certain markets only) | U = Ulow | U = Ubat | Active in ignition switch position I, II and III. |
| - | #C3:3 | Stop lamp, left | During activation U = Ubat | During activation U = Ubat | - |
| - | #C3:4 | - | - | - | - |
| - | #C3:5 | - | - | - | - |
| - | #C3:6 | Back-up (reversing) lamp (certain markets only) | U = Ulow | During activation U = Ubat | - |
| - | #C3:7 | Stop lamp, right | During activation U = Ubat | During activation U = Ubat | - |
| - | #C3:8 | Fog lamp (certain markets only) | U = Ulow | During activation U = Ubat | - |
| - | #C3:9 | - | - | - | - |
| - | #C3:10 | Left turn signal lamp | U = Ulow | During activation and normal function f = 1, 5 Hz, PWM = 50 % | - |
| - | #C3:11 | - | - | - | - |
| - | #C3:12 | Parking lamps | Normally U = Ulow During activation U = Ubat |
U = Ubat | - |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
