Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSVOLVO2009C30 R-DESIGN, AUTOMATICREPAIR AND DIAGNOSISBRAKESTRACTION CONTROLBRAKE CONTROL MODULE (BCM) - DIAGNOSTIC TROUBLE CODE (DTC) INDEXBRAKE CONTROL MODULE (BCM) DTCS
2009 Volvo C30 R-Design, Automatic
Brake Control Module (BCM) DTCS
2009 Volvo C30 R-Design, AutomaticSECTION Brake Control Module (BCM) DTCS
BRAKE CONTROL MODULE (BCM) - DTC INDEX
| Volvo Code | Description |
|---|---|
| BCM-0010 | Wheel sensor left front. Faulty signal |
| BCM-0011 | Wheel sensor left front. Faulty signal |
| BCM-0012 | Wheel sensor left front. Mechanical fault |
| BCM-0030 | Wheel sensor left rear. Faulty signal |
| BCM-0050 | Control module. Faulty signal |
| BCM-0052 | Control module. Internal fault |
| BCM-0057 | Power supply. Voltage too low |
| BCM-0058 | Power supply. Voltage too high |
| BCM-0061 | Brake discs. Temperature too high |
| BCM-0068 | Sensor power supply. Faulty signal |
| BCM-0070 | Power supply for the pump motor. Faulty signal |
| BCM-0071 | Pump motor. Signal missing |
| BCM-0072 | Pump motor. Mechanical fault |
| BCM-0074 | Hydraulic valves. Faulty signal |
| BCM-0076 | Control module. Faulty configuration |
| BCM-0080 | Lateral accelerometer. Incorrect offset value |
| BCM-0090 | Lateral accelerometer. Faulty signal |
| BCM-0091 | Accelerometer. Faulty signal |
| BCM-0094 | Communication between control modules. Communication problems with the differential electronic module (DEM) |
| BCM-0095 | Communication between control modules. Communication problems with the differential electronic module (DEM) |
| BCM-0096 | Sensor cluster. Faulty signal |
| BCM-0097 | Communication between control modules. Communication problems with the central electronic module (CEM) |
| BCM-0100 | Communication between control modules. Communication problems with the engine control module (ECM) |
| BCM-0101 | Communication between control modules. Communication problems with the engine control module (ECM) |
| BCM-0103 | Pedal position sensor. Faulty signal |
| BCM-0105 | Steering wheel, wheel alignment. Signal outside its permitted range |
| BCM-0106 | Steering wheel, wheel alignment. Incorrect steering wheel or wheel alignment |
| BCM-0108 | Communication between control modules. Communication problems with the steering wheel module (SWM), control module not initiated |
| BCM-0109 | Communication between control modules. Steering wheel module (SWM), internal fault |
| BCM-0111 | Communication between control modules. AYC stability control active for too long |
| BCM-0112 | Body sensor cluster stability sensor (BSC). Sensor not calibrated |
| BCM-0113 | Back-up (reversing) signal. Signal missing |
| BCM-0114 | Communication with the body sensor cluster stability sensor (BSC). Signal missing |
| BCM-0115 | Communication between control modules. Communication with the steering wheel module (SWM), signal missing |
| BCM-0116 | Communication with the body sensor cluster stability sensor (BSC). Communication problems |
| BCM-0117 | Communication with the body sensor cluster stability sensor (BSC). Incorrect body sensor cluster stability sensor (BSC) installed |
| BCM-0118 | Power supply for the body sensor cluster stability sensor (BSC). Voltage too high |
| BCM-0119 | Power supply for the body sensor cluster stability sensor (BSC). Voltage too low |
| BCM-0121 | Yaw rate sensor. Signal outside its permitted range |
| BCM-0123 | Body sensor cluster stability sensor (BSC). Internal fault |
| BCM-0130 | Brake pressure sensor. Signal missing |
| BCM-0134 | Brake pressure sensor. Incorrect offset value |
| BCM-0135 | Brake pressure sensor. Signal outside its permitted range |
| BCM-0138 | Power supply for the body sensor cluster stability sensor (BSC). Faulty voltage |
| BCM-0145 | Stability control. Stability control has been active for too long |
| BCM-0146 | Factory test, dynamic stability and traction control (DSTC). Test cycle not approved |
| BCM-0147 | Pedal position sensor. Signal outside its permitted range |
| BCM-0148 | Communication between control modules. Faulty configuration ID |
| BCM-0150 | Stop lamp switch. Signal outside its permitted range |
| BCM-0151 | Control module. Internal memory fault |
| BCM-A030 | Communication between control modules. The initialization check has not been run |
| BCM-A031 | Communication between control modules. The tolerance check has not been run |
| BCM-A032 | Communication between control modules. Stability control has been active for too long |
| BCM-E000 | Control module communication. Faulty communication |
| BCM-E003 | Control module. Faulty configuration |
| BCM-XXXX | Unknown diagnostic trouble code (DTC) for the current control module version |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.