Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Volvo V50 Base, 2.4 39FACTORY OEM SERVICE PROCEDURE
Combustion PREHEATER Module (CPM) DTCS
COMBUSTION PREHEATER MODULE (CPM) - DTC INDEX
| DTC | Description |
|---|---|
| CPM-0018 | Glow plugs. Signal too high |
| CPM-0102 | Glow plugs. Signal too low |
| CPM-0204 | Glow plugs. Signal missing |
| CPM-0318 | Fuel pump. Signal too high |
| CPM-0402 | Fuel pump. Signal too low |
| CPM-0504 | Fuel pump. Signal missing |
| CPM-1001 | Combustion fan. Signal too high |
| CPM-1128 | Combustion fan. Signal too low |
| CPM-1204 | Combustion fan. Signal missing |
| CPM-1308 | Combustion fan. Faulty function |
| CPM-1418 | Water pump. Signal too high |
| CPM-1502 | Water pump. Signal too low |
| CPM-1604 | Water pump. Signal missing |
| CPM-2308 | Control module. Internal fault |
| CPM-3002 | Engine coolant temperature (ECT) sensor. Signal too low |
| CPM-3141 | Engine coolant temperature (ECT) sensor. Signal too high / Signal missing |
| CPM-3202 | Overheat protection thermostat. Signal too low |
| CPM-3341 | Overheat protection thermostat. Signal too high / Signal missing |
| CPM-3402 | Flame sensor. Signal too low |
| CPM-3541 | Flame sensor. Signal too high / Signal missing |
| CPM-3601 | Control module. Supply voltage too high |
| CPM-3702 | Control module. Supply voltage too low |
| CPM-4001 | Engine coolant heater. Activated too long |
| CPM-4101 | Engine coolant heater. Too many unsuccessful attempts |
| CPM-4208 | Engine coolant heater. Extinguished flame |
| CPM-4308 | Engine coolant heater. Extinguished flame |
| CPM-4501 | Combustion fan. Activated too long |
| CPM-5001 | Control module. Over heated |
| CPM-5101 | Control module. Over heated |
| CPM-5201 | Control module. Over heated |
| CPM-5301 | Control module. Over heated |
| CPM-5401 | Control module. Internal fault |
| CPM-5601 | Control module. Internal fault |
| CPM-5701 | Control module. Collision signal received |
| CPM-6008 | Control module. Internal fault |
| CPM-6108 | Control module. Internal fault |
| CPM-6208 | Control module. Internal fault |
| CPM-6301 | Control module. Internal fault |
| CPM-6408 | Control module. Internal fault |
| CPM-6508 | Control module. Internal fault |
| CPM-8602 | Control module. Internal fault |
| CPM-8704 | Control module. Internal fault |
| CPM-E001 | Control module communication. Faulty communication |
| CPM-E003 | Configuration fault. Faulty configuration |
| CPM-E010 | Control module. Supply voltage too low |
| CPM-XXXX | Unknown diagnostic trouble code (DTC) for the current control module version |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
