Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Volvo XC90 Base, 4.4 85FACTORY OEM SERVICE PROCEDURE
Infotainment Control Module (ICM) DTCS
INFOTAINMENT CONTROL MODULE (ICM) DTC INDEX
| DTC | Description |
|---|---|
| ICM-1A02 | Control module. Faulty voltage |
| ICM-1A03 | Control module. Faulty voltage |
| ICM-1A05 | Control module. Faulty voltage |
| ICM-1A51 | Communication with the audio module (AUD). Signal missing |
| ICM-1A52 | Communication with the antenna module (ATM). Signal missing |
| ICM-1A53 | Communication with the multimedia module (MMM). Signal missing |
| ICM-1A54 | Communication with the Subwoofer module (SUB). Signal missing |
| ICM-1A55 | Communication with the MD module (MP1). Signal missing |
| ICM-1A56 | Communication with the CD module (MP2). Signal missing |
| ICM-1A57 | Communication with the phone module (PHM). Signal missing |
| ICM-1D01 | Control module. Internal fault |
| ICM-1D03 | Control module, not fully programmed. Internal fault |
| ICM-1D07 | Control module. Internal fault |
| ICM-1D08 | Control module. Internal fault |
| ICM-1D09 | Control module. Internal fault |
| ICM-1F20 | Left keypad. Activated too long |
| ICM-1F21 | Left-hand keypad circuit 1. Signal too high/too low |
| ICM-1F22 | Left-hand keypad circuit 2. Signal too high/too low |
| ICM-1F23 | Left-hand keypad circuit 3. Signal too high/too low |
| ICM-1F24 | Left-hand keypad circuit 4. Signal too high/too low |
| ICM-1F25 | Right-hand keypad circuit 5. Signal too high/too low |
| ICM-1F26 | Right keypad. Activated too long |
| ICM-1F27 | Right-hand keypad circuit 1. Signal too high/too low |
| ICM-1F28 | Right-hand keypad circuit 2. Signal too high/too low |
| ICM-1F29 | POWER button. Signal too high/low |
| ICM-1F30 | POWER button. Activated too long |
| ICM-1F31 | SOUND button. Activated too long |
| ICM-1F32 | VOLUME knob. Signal missing |
| ICM-1F33 | SELECTOR knob. Signal missing |
| ICM-1F34 | VOLUME knob. Faulty signal |
| ICM-1F35 | SELECTOR knob. Faulty signal |
| ICM-6C70 | Antenna Module (ATM) not approved. Faulty signal |
| ICM-6C71 | Audio module (AUD) not approved. Faulty signal |
| ICM-6C72 | Multimedia module (MMM) not approved. Faulty signal |
| ICM-6C73 | Subwoofer module (SUB) not approved. Faulty signal |
| ICM-6C74 | MD module (MP1) not approved. Faulty signal |
| ICM-6C75 | CD module (MP2) not approved. Faulty signal |
| ICM-6C76 | Phone module (PHM) not approved. Faulty signal |
| ICM-6C79 | Infotainment control module (ICM) not valid. Faulty signal |
| ICM-DC00 | Control module communication. Internal fault |
| ICM-DC01 | Control module communication. Faulty signal |
| ICM-DC02 | Control module communication. Signal missing |
| ICM-E001 | Control module communication. Internal fault |
| ICM-E003 | Configuration fault. Software fault |
| ICM-E010 | Power supply. Signal too low |
| ICM-XXXX | Unknown diagnostic trouble code (DTC) for the current control module version |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
