Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2005 Volvo V50 Base, 2.4 39FACTORY OEM SERVICE PROCEDURE
Central Electronic Module (CEM) DTCS
CENTRAL ELECTRONIC MODULE (CEM) - DTC INDEX
| DTC | Description |
|---|---|
| CEM-1011 | Control module memory fault. Internal fault |
| CEM-1011 | (A) Control module memory fault. Internal fault |
| CEM-1011 | (B) Control module memory fault. Internal fault |
| CEM-1012 | Control module, memory fault. Internal fault |
| CEM-1012 | (A) Control module memory fault. Internal fault |
| CEM-1012 | (B) Control module memory fault. Internal fault |
| CEM-101A | Control module, memory fault. Internal fault |
| CEM-101B | Control module, memory fault. Internal fault |
| CEM-1201 | Control module. Configuration fault |
| CEM-1A21 | Engine control module (ECM). Signal too low |
| CEM-1A22 | Engine control module (ECM). Signal too high |
| CEM-1A40 | 50-power supply. Activated too long |
| CEM-1A41 | Ignition switch. Faulty signal |
| CEM-1A41 | (A) Ignition switch. Faulty signal |
| CEM-1A42 | Real time clock. Faulty signal |
| CEM-1B01 | Main Battery Diode. General electrical failure |
| CEM-1B02 | Main battery relay. General electrical failure |
| CEM-1B03 | Main battery diode or relay. General electrical failure |
| CEM-1C04 | 30-power supply. Signal too high |
| CEM-1C10 | Control module. Configuration fault |
| CEM-1D08 | Control module. Internal fault |
| CEM-1D08 | (A) Control module. Internal fault |
| CEM-1D08 | (B) Control module. Internal fault |
| CEM-1D09 | Control module. Internal fault |
| CEM-2E01 | Relay, horn. Signal too low |
| CEM-2E02 | Relay, horn. Signal too high |
| CEM-2E03 | Comfort relay. Signal too low |
| CEM-2E04 | Comfort relay. Signal too high |
| CEM-2F60 | Twilight sensor. Signal too high |
| CEM-2F61 | Twilight sensor. Signal too low |
| CEM-3A00 | ECM software. Faulty signal |
| CEM-3A04 | Fuel pump (FP). Signal too high |
| CEM-3A05 | Fuel pump (FP). Signal too low |
| CEM-3A07 | Fuel pump (FP). Faulty signal |
| CEM-3A08 | Fuel pump (FP). Signal too high |
| CEM-3F01 | Clutch pedal sensor. Signal too low |
| CEM-3F01 | (A) Clutch pedal sensor. Signal too low (B5244S4, M56; B5254T3, M66) |
| CEM-3F01 | (B) Back up gear inhibitor. Faulty signal (M66) |
| CEM-3F02 | Clutch pedal sensor. Faulty signal |
| CEM-3F02 | (A) Clutch pedal sensor. Faulty signal (B5244S4, M56; B5254T3, M66) |
| CEM-3F02 | (B) Back up gear inhibitor. Signal too low (M66) |
| CEM-3F03 | Clutch pedal sensor. Signal too high (B5244S4, M56) |
| CEM-3F03 | Clutch pedal sensor. Signal too high (B5254T3, M66) |
| CEM-3F03 | Clutch pedal sensor. Signal too high (B5254T7, M66) |
| CEM-3F0A | Reverse gear inhibit. Faulty signal (M66) |
| CEM-3F0B | Reverse gear inhibit. Signal too low (M66) |
| CEM-3F41 | Supply pedal sensor. Signal too low |
| CEM-3F42 | Supply pedal sensor. Signal too high |
| CEM-3F92 | Accelerator pedal (AP) position sensor. Signal too high |
| CEM-3F93 | Accelerator pedal (AP) position sensor. Signal too low |
| CEM-4A00 | Total mileage. Comparison fault |
| CEM-4A33 | Fuel level sensor. Faulty signal |
| CEM-4A33 | Fuel level sensor. Faulty signal (B5244S4; B5244S7) |
| CEM-4A33 | Fuel level sensor. Faulty signal (B5254T3) |
| CEM-4A33 | Fuel level sensor. Faulty signal (B5254T7) |
| CEM-4A34 | Fuel level sensor. Signal too low |
| CEM-4A34 | Fuel level sensor. Signal too low (B5244S4; B5244S7) |
| CEM-4A34 | Fuel level sensor. Signal too low (B5254T3) |
| CEM-4A34 | Fuel level sensor. Signal too low (B5254T7) |
| CEM-4C01 | Outside temperature sensor. Signal too high |
| CEM-4C01 | Outside temperature sensor. Signal too high |
| CEM-4C02 | Outside temperature sensor. Signal too low |
| CEM-4E24 | Malfunction indicator lamp (MIL). Faulty signal |
| CEM-4E25 | Malfunction indicator lamp (MIL). Signal too high |
| CEM-4F30 | Battery temperature. Signal too high |
| CEM-4F31 | Battery temperature. Signal too low |
| CEM-4F32 | Battery temperature. Faulty signal |
| CEM-4F33 | Battery temperature. Faulty signal |
| CEM-4F40 | Seat belt buckle, right rear seat. Signal too low |
| CEM-4F41 | Seat belt buckle, right rear seat. Signal too high |
| CEM-4F42 | Seat belt buckle, rear right-hand. Faulty signal |
| CEM-4F44 | Seat belt buckle, rear center. Signal too low |
| CEM-4F45 | Seat belt buckle, rear center. Signal too high |
| CEM-4F46 | Seat belt buckle, rear center. Faulty signal |
| CEM-4F48 | Seat belt buckle, rear left-hand. Signal too low |
| CEM-4F49 | Seat belt buckle, rear left-hand. Signal too high |
| CEM-4F4A | Seat belt buckle, rear left-hand. Faulty signal |
| CEM-4F81 | Lamp, seat belt reminder. Signal too low |
| CEM-4F81 | Lamp, seat belt reminder. Signal too low |
| CEM-4F82 | Lamp, seat belt reminder. Faulty signal |
| CEM-4F82 | Lamp, seat belt reminder. Faulty signal |
| CEM-5A10 | Blower fan motor. Blocked |
| CEM-5A10 | Blower fan motor. Blocked (B5244S4, L.H.D; B5244S7, L.H.D) |
| CEM-5A10 | Blower fan motor. Blocked (B5254T3, L.H.D) |
| CEM-5A10 | Blower fan motor. Blocked (B5254T7, L.H.D) |
| CEM-5A12 | Blower fan motor. Over heated |
| CEM-5A12 | Blower fan motor. Over heated (B5244S4, L.H.D; B5244S7, L.H.D) |
| CEM-5A12 | Blower fan motor. Over heated (B5254T3, L.H.D) |
| CEM-5A12 | Blower fan motor. Over heated (B5254T7, L.H.D) |
| CEM-5A13 | Blower fan motor. Voltage too high |
| CEM-5A13 | Blower fan motor. Voltage too high (B5244S4, L.H.D; B5244S7, L.H.D) |
| CEM-5A13 | Blower fan motor. Voltage too high (B5254T3, L.H.D) |
| CEM-5A13 | Blower fan motor. Voltage too high (B5254T7, L.H.D) |
| CEM-5A15 | Blower fan motor. Current too high |
| CEM-5A15 | Blower fan motor. Current too high (B5244S4, L.H.D; B5244S7, L.H.D) |
| CEM-5A15 | Blower fan motor. Current too high (B5254T3, L.H.D) |
| CEM-5A15 | Blower fan motor. Current too high (B5254T7, L.H.D) |
| CEM-5A17 | Blower fan motor. Signal too high/signal missing |
| CEM-5A17 | Blower fan motor. Signal too high/signal missing (B5244S4, L.H.D; B5244S7, L.H.D) |
| CEM-5E01 | Sun sensor. Faulty signal |
| CEM-5E02 | Sun sensor. Signal too low |
| CEM-5E03 | Sun sensor. Signal too high |
| CEM-5E04 | Sun sensor. Signal too low |
| CEM-6C05 | Central locking driver's door. No locking |
| CEM-6C06 | Central locking passenger door. No locking |
| CEM-6C07 | Central locking left-hand rear door. No locking |
| CEM-6C08 | Central locking right-hand rear door. No locking |
| CEM-6C13 | Deadlock, driver's door. No locking |
| CEM-6C14 | Deadlock, passenger door. No locking |
| CEM-6C15 | Deadlock, left-hand rear door. No locking |
| CEM-6C16 | Deadlock, right-hand rear door. No locking |
| CEM-6C19 | Child-proof lock, left-hand rear door. No locking |
| CEM-6C20 | Child-proof lock, right-hand rear door. No locking |
| CEM-6C28 | Alarm LED. Faulty signal |
| CEM-6C29 | Alarm LED. Signal too low |
| CEM-6C30 | Siren. Internal fault |
| CEM-6C31 | Siren. Internal fault |
| CEM-6C32 | Movement sensor. Signal missing |
| CEM-6C33 | Movement sensor. Signal missing |
| CEM-6C34 | Switch reduced alarm. Activated too long |
| CEM-6C41 | Start control module (SCU). Incorrect key ID |
| CEM-6C42 | Start control module (SCU). Signal missing |
| CEM-6C43 | Start control module (SCU). Faulty signal |
| CEM-6C44 | Steering column lock module (SCL). Faulty signal |
| CEM-6C45 | (B) Steering column lock module (SCL). Signal too low |
| CEM-6C46 | Steering column lock module (SCL). Faulty signal |
| CEM-6C47 | Steering column lock module (SCL). Faulty signal |
| CEM-6C49 | Steering column lock module (SCL). Faulty signal |
| CEM-6C4C | Steering column lock module (SCL). Signal too low |
| CEM-6C50 | Steering column lock module (SCL). Not programmed |
| CEM-6C51 | Steering column lock module (SCL). Faulty signal |
| CEM-6C52 | Steering column lock module (SCL). Faulty signal |
| CEM-6C53 | Steering column lock module (SCL). Internal fault |
| CEM-6C54 | Engine control module (ECM) communication. Incorrect value |
| CEM-6C55 | KVM communication. Faulty value |
| CEM-6C56 | Steering column lock module (SCL). Faulty communication |
| CEM-6C57 | Phone module (PHM) not valid. Faulty signal |
| CEM-6F10 | Sun roof. Signal too high |
| CEM-6F10 | Sun roof. Signal too high |
| CEM-6F11 | Sun roof. Faulty signal |
| CEM-6F12 | Sun roof. Faulty signal |
| CEM-6F13 | Sun roof. Signal too high |
| CEM-6F51 | Tailgate handle. Faulty signal |
| CEM-6F52 | Tailgate handle. Signal too low |
| CEM-6F53 | Tailgate handle. Activated too long |
| CEM-6F83 | Dimmer. Faulty signal |
| CEM-6F83 | Dimmer. Faulty signal |
| CEM-6F84 | Fuel flap driver. Faulty signal |
| CEM-6F85 | Dimmer. Signal too low |
| CEM-6F86 | Fuel tank filler cap. Signal too low |
| CEM-6F87 | Fuel tank filler cap. Activated too long |
| CEM-8A02 | Relay, high beam. Internal fault |
| CEM-8A03 | Relay, high beam. Internal fault |
| CEM-8A04 | LED light switch, automatic bending light. Signal too high |
| CEM-8A05 | LED light switch, automatic bending light. Faulty signal |
| CEM-8A08 | Low beam right. Signal too low |
| CEM-8A09 | Low beam right. Faulty signal |
| CEM-8A11 | Low beam left. Signal too low |
| CEM-8A12 | Low beam left. Faulty signal |
| CEM-8A20 | Gas discharge lamp module (GDL) left-hand. Parameter fault |
| CEM-8A21 | Gas discharge lamp module (GDL) left-hand. Calibration fault |
| CEM-8A22 | Gas discharge lamp module (GDL) left-hand. Internal fault |
| CEM-8A23 | Gas discharge lamp module (GDL) right-hand. Internal fault |
| CEM-8A24 | Gas discharge lamp module (GDL) left-hand. Faulty signal |
| CEM-8A25 | Gas discharge lamp module (GDL) right-hand. Faulty signal |
| CEM-8A26 | Gas discharge lamp module (GDL) left-hand. Faulty signal |
| CEM-8A27 | Gas discharge lamp module (GDL) right-hand. Faulty signal |
| CEM-8A28 | Gas discharge lamp module (GDL) left-hand. Faulty signal |
| CEM-8A29 | Gas discharge lamp module (GDL) right-hand. Faulty signal |
| CEM-8A30 | Gas discharge lamp module (GDL) left-hand. Faulty signal |
| CEM-8A31 | Gas discharge lamp module (GDL) left-hand. Voltage too high |
| CEM-8A32 | Gas discharge lamp module (GDL) right-hand. Voltage too high |
| CEM-8A33 | Gas discharge lamp module (GDL) left-hand. Signal too low |
| CEM-8A34 | Gas discharge lamp module (GDL) right-hand. Signal too high |
| CEM-8A35 | Gas discharge lamp module (GDL) left-hand. Faulty position |
| CEM-8A36 | Gas discharge lamp module (GDL) right-hand. Faulty position |
| CEM-8A37 | Gas discharge lamp module (GDL) left-hand. Faulty signal |
| CEM-8A38 | Gas discharge lamp module (GDL) right-hand. Faulty signal |
| CEM-8A39 | Gas discharge lamp module (GDL) left-hand. Calibration fault |
| CEM-8A40 | Gas discharge lamp module (GDL) left-hand. Calibration fault |
| CEM-8B02 | Left parking lamps. Signal too low |
| CEM-8B03 | Left parking lamps. Faulty signal |
| CEM-8B05 | Right parking lamps. Faulty signal |
| CEM-8B06 | Right parking lamps. Signal too low |
| CEM-8B08 | Light switch module (LSM). Signal too low |
| CEM-8B09 | Light switch module (LSM). Faulty signal |
| CEM-8C10 | Relay, front fog lamps. Signal too high |
| CEM-8C11 | Relay, front fog lamps. Faulty signal |
| CEM-8C20 | Rear fog lamp. Faulty signal |
| CEM-8C21 | Rear fog lamp. Signal too low |
| CEM-8D01 | Stop lamp switch. Comparison fault |
| CEM-8D03 | High level stop lamp. Signal too high |
| CEM-8D03 | High level stop lamp. Signal too high |
| CEM-8D04 | High level stop lamp. Signal too low |
| CEM-8D04 | High level stop lamp. Signal too low |
| CEM-8D05 | Right-hand stop lamp. Signal too low |
| CEM-8D05 | Right-hand stop lamp. Signal too low |
| CEM-8D06 | Right-hand stop lamp. Faulty signal |
| CEM-8D06 | Right-hand stop lamp. Faulty signal |
| CEM-8D07 | Left-hand stop lamp. Signal too low |
| CEM-8D07 | Left-hand stop lamp. Signal too low |
| CEM-8D08 | Left-hand stop lamp. Faulty signal |
| CEM-8D08 | Left-hand stop lamp. Faulty signal |
| CEM-8D09 | Brake lamp left. Faulty signal |
| CEM-8D0A | Brake lamp left. Faulty signal |
| CEM-8D10 | Brake light switch. Compare error |
| CEM-8F01 | Switch, hazard warning signal flashers. Faulty signal |
| CEM-8F02 | Switch, hazard warning signal flashers. Signal too low |
| CEM-8F21 | Wiper motor module (WMM). Internal fault |
| CEM-8F22 | Wiper motor module (WMM). Voltage too low |
| CEM-8F23 | Wiper motor module (WMM). Voltage too high |
| CEM-8F24 | Wiper motor module (WMM). Jammed |
| CEM-8F26 | Relay, front windshield washer motor. Internal fault |
| CEM-8F27 | Relay, front windshield washer motor. Internal fault |
| CEM-8F28 | Tailgate washer motor relay. Internal fault |
| CEM-8F29 | Tailgate washer motor relay. Internal fault |
| CEM-8F30 | Relay, headlamp wash/wipe. Faulty signal |
| CEM-8F31 | Relay, headlamp wash/wipe. Signal too high |
| CEM-8F31 | Relay, headlamp wash/wipe. Signal too high |
| CEM-8F33 | Right-hand turn signal lamp. Faulty signal |
| CEM-8F34 | Right-hand turn signal lamp. Signal too low |
| CEM-8F37 | Left-hand turn signal lamp. Faulty signal |
| CEM-8F38 | Left-hand turn signal lamp. Signal too low |
| CEM-8F41 | Relay, tailgate wiper. Internal fault |
| CEM-8F42 | Relay, tailgate wiper. Faulty signal |
| CEM-8F61 | Relay, heated rear windshield. Faulty signal |
| CEM-8F62 | Relay, heated rear windshield. Signal too high |
| CEM-8FA2 | Relay, horn. Activated too long |
| CEM-8FB1 | Rain sensor module (RSM). Internal fault |
| CEM-8FB2 | Rain sensor module (RSM). Faulty function |
| CEM-9A01 | Interior lighting. Signal too high |
| CEM-9A02 | Interior lighting. Signal too low |
| CEM-9D01 | Communication with RRX control module. Comminicational problems |
| CEM-9F31 | Dimmer. Signal too high |
| CEM-9F32 | Dimmer. Faulty signal |
| CEM-9F33 | Brake fluid level too low |
| CEM-AFE0 | TPMS default values in local configuration |
| CEM-AFE1 | TPMS incorrect configuration |
| CEM-AFF1 | Localization failed |
| CEM-AFF2 | Tire pressurement sensor. Faulty signal |
| CEM-AFF6 | Tire pressurement sensor. Signal missing |
| CEM-AFFE | Missing tire pressure sensor. Signal missing |
| CEM-CFF0 | MMS communication. Faulty signal |
| CEM-DD00 | LIN-Bus 2. Communication fault |
| CEM-DD00 | LIN-Bus 3. Communication fault |
| CEM-DD00 | (A) LIN bus 2. Communication fault |
| CEM-DD00 | (B) LIN bus 3. Communication fault |
| CEM-DD01 | LIN-bus 2. Communication missing |
| CEM-DD01 | LIN-bus 3. Communication missing |
| CEM-DD01 | (A) LIN bus 2. Communication missing |
| CEM-DD01 | (B) LIN bus 3. Communication missing |
| CEM-DD02 | LIN-bus 2. Communication fault |
| CEM-DD02 | LIN-bus 3. Communication fault |
| CEM-DD02 | (A) LIN bus 1. Communication fault |
| CEM-DD02 | (B) LIN bus 3. Communication fault |
| CEM-DD03 | LIN-bus 14. Communication fault |
| CEM-DD04 | LIN-bus 14. Communication missing |
| CEM-DD05 | LIN-bus 14. Communication fault |
| CEM-DD06 | Communication with battery monitoring sensor (BMS). Signal missing |
| CEM-DD07 | Battery monitoring sensor (BMS). Faulty hardware |
| CEM-DD0A | LIN-bus 3. Communication fault |
| CEM-DD0B | LIN-bus 3. Communication missing |
| CEM-DD0C | LIN-bus 3. Communication fault |
| CEM-DD10 | Communication with SCL control module. Signal missing |
| CEM-DD10 | (A) Communication with the steering column lock module (SCL). Signal missing |
| CEM-DD10 | (B) Communication with the RRX control module. Signal missing |
| CEM-DD11 | Communication with SCU control module. Signal missing |
| CEM-DD11 | (A) Communication with the start control module (SCU). Signal missing |
| CEM-DD11 | (B) Communication with the siren control module (SCM). Signal missing |
| CEM-DD12 | Communication with the left-hand gas discharge lamp module (GDL). Signal missing |
| CEM-DD13 | Communication with the right-hand gas discharge lamp module (GDL). Signal missing |
| CEM-DD1A | Communication with RRX control module. Signal missing |
| CEM-DD1A | Communication with RRX control module. Signal missing |
| CEM-DD1B | Communication with SCM control module. Signal missing |
| CEM-DD1C | Communication with SCM control module. Faulty signal |
| CEM-DD20 | LIN bus 9. Communication fault |
| CEM-DD21 | LIN bus 9. No communication |
| CEM-DD22 | LIN bus 9. Communication fault |
| CEM-DD30 | Communication with the wiper motor module (WMM). Signal missing |
| CEM-DD31 | Communication with the rain sensor module (RSM). Signal missing |
| CEM-DD32 | Communication with humidity sensor (HUS). Signal missing |
| CEM-DD40 | Humidity sensor (HUS). Internal fault. |
| CEM-DE01 | Communication with the brake control module (BCM). Signal missing |
| CEM-DE0B | Communication with the additive dosing module (ADM). Signal missing |
| CEM-DE11 | Communication with ECM control module. Signal missing |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5244S4) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5244S7) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5254T3) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5254T7) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5244S4) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5244S7) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5254T3) |
| CEM-DE11 | Communication with ECM control module. Signal missing (B5254T7) |
| CEM-DE18 | Communication with the combustion preheater module (CPM). Signal missing |
| CEM-DE1A | Communication with DEM control module. Signal missing |
| CEM-DE23 | Communication with the trailer module (TRM). Signal missing |
| CEM-DE29 | Communication with the climate control module (CCM). Signal missing |
| CEM-DE2D | Communication with KVM control module. Signal missing |
| CEM-DE2E | Communication with the power seat module (PSM). Signal missing |
| CEM-DE30 | Communication with the electric power steering module (EPS). Signal missing |
| CEM-DE43 | Communication with the driver door module (DDM). Signal missing |
| CEM-DE45 | Communication with the passenger door module (PDM). Signal missing |
| CEM-DE49 | Communication with the steering wheel module (SWM). Signal missing |
| CEM-DE51 | Communication with the driver information module (DIM). Signal missing |
| CEM-DE52 | Communication with the Accessory Electronic Module (AEM). Signal missing |
| CEM-DE54 | Communication with the infotainment control module (ICM). Signal missing |
| CEM-DE58 | Communication with the supplemental restraint system module (SRS). Signal missing |
| CEM-DE63 | communication with the parking assistance module (PAM). Signal missing |
| CEM-DE64 | Communication with the phone module (PHM). Signal missing |
| CEM-DE6E | Communication with the transmission control module (TCM). Signal missing |
| CEM-DE70 | Communication with headlamp control module (HCM). Signal missing |
| CEM-DF01 | CAN-H, low speed network. Signal missing |
| CEM-DF03 | CAN-H, low speed network. Signal too high |
| CEM-DF04 | CAN-L, low speed network. Signal too low |
| CEM-DF05 | CAN-H, low speed network. Signal too low |
| CEM-DF06 | CAN-L, low speed network. Signal too high |
| CEM-DF07 | CAN-L, low speed network. Faulty signal |
| CEM-DF11 | CAN-H, high speed network. Signal missing |
| CEM-DF13 | CAN-H, high speed network. Signal too high |
| CEM-DF14 | CAN-L, high speed network. Signal too low |
| CEM-DF15 | CAN-H, high speed network. Signal too low |
| CEM-DF16 | CAN-L, high speed network. Signal too high |
| CEM-DF17 | CAN-L, high speed network. Faulty signal |
| CEM-E000 | Communication with control module. Faulty communication |
| CEM-E001 | Communication with control module. Faulty communication |
| CEM-E001 | (A) Communication with the control module. Faulty communication |
| CEM-E001 | (B) Communication with the control module. Faulty communication |
| CEM-E00A | Communication with control module. Faulty communication |
| CEM-XXXX | (A) Unknown diagnostic trouble code (DTC) for the current control module version |
| CEM-XXXX | (B) Unknown diagnostic trouble code (DTC) for the current control module version |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
