Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
1999 Volvo S80 BaseFACTORY OEM SERVICE PROCEDURE
Driver Door Module (DDM) & Passenger Door Module (PDM) DTCS
DRIVER DOOR MODULE (DDM) & PASSENGER DOOR MODULE (PDM) - DTC INDEX
| DTC | Description |
|---|---|
| DDM/PDM-0005 | Power window lift motor M+ or M-. Signal missing |
| DDM/PDM-0005 | Window-lifting motor M+. Signal missing |
| DDM/PDM-0006 | Power window up relay. Signal too high |
| DDM/PDM-0007 | Power window up relay. Faulty signal |
| DDM/PDM-000A | Window lift down relay. Signal too high |
| DDM/PDM-000B | Power window down relay. Faulty signal |
| DDM/PDM-000D | Central locking motor M1 or M3. Signal too high |
| DDM/PDM-0010 | Central locking motor M1. Signal too low |
| DDM/PDM-0011 | Central locking relay RL2_RD2. Signal too high |
| DDM/PDM-0012 | Central locking relay RL2_RD2. Signal too low |
| DDM/PDM-0013 | Central locking motor M3. Signal too low |
| DDM/PDM-0014 | Central locking relay RL2_RD4. Signal too high |
| DDM/PDM-0015 | Central locking relay RL2_RD4. Signal too low |
| DDM/PDM-0016 | Central locking motor M2. Signal too low |
| DDM/PDM-0017 | Central locking relay RL3. Signal too high |
| DDM/PDM-0018 | Central locking relay RL3. Signal too low |
| DDM/PDM-0019 | Lock, driver's door. Signal too low |
| DDM/PDM-001A | Lock, driver's door. Signal too low |
| DDM/PDM-001B | Lock, driver's door. Signal too low |
| DDM/PDM-0020 | Window lift hall sensor 1. Signal faulty |
| DDM/PDM-0021 | Window lift hall sensor 2. Signal faulty |
| DDM/PDM-0022 | Window lift hall sensors 1 and 2. Signal faulty |
| DDM/PDM-0023 | Mirror motor MX+. Signal too high |
| DDM/PDM-0024 | Mirror motor MX+. Signal too low |
| DDM/PDM-0025 | Door mirror motor. Disconnected |
| DDM/PDM-0026 | Mirror motor MY+. Signal too high |
| DDM/PDM-0027 | Mirror motor MY+. Signal too low |
| DDM/PDM-0028 | Mirror motor MF+. Signal too high |
| DDM/PDM-0029 | Mirror motor MF+. Signal too low |
| DDM/PDM-002A | Mirror motor MC. Signal too high |
| DDM/PDM-002B | Mirror motor MC. Signal too low |
| DDM/PDM-002C | Mirror heater. Signal too high |
| DDM/PDM-002D | Mirror heater. Signal too low |
| DDM/PDM-002E | Mirror heater. Signal too high |
| DDM/PDM-002F | Window motor. Signal too high |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.