2025 Volkswagen ID.4 StandardFACTORY OEM SERVICE PROCEDURE

Maintenance Tables: Services

NOTE:

The scope of services is universally valid and differs depending on the vehicle model and vehicle equipment. There is no vehicle-specific reference to an identified VIN.

Vehicle-specific services are only listed in the Maintenance Tables. Refer to the MAINTENANCE TABLES .

Inspection Work to be completed
Vehicle Interior  
X -- Interior Lamps in Headliner, Luggage Compartment and Glove Compartment Lamps, Checking Function
X -- Horn, Checking Function
X -- Charging Cable, Checking Presence and Condition
  • Only applies to BEV and PHEV
X -- High-Voltage Battery Charge Level, Checking and Charging if Necessary
  • Only applies to BEV
Vehicle Exterior  
X -- Headlamp Washer System, Checking Function
X -- Front Lighting, Checking Function
X -- Stationary Cornering Lamp, Checking Function
X -- Automatic Headlamp Control, Checking Function
X -- Rear Lamps, Checking Function
X -- Windshield Wiper/Washer System, Checking Function, Spray Nozzle Adjustment and for Damage, and Adjusting if Necessary
X -- Wiper Blades, Bringing into Service Position, Checking for Damage and Checking Park Position
X -- Body Interior and Exterior, Visually Inspecting for Corrosion
X -- Windshield, Visually Inspecting for Damage
X -- High-Voltage Charging Sockets in Radiator Grille and Fuel Filler Cap Visual Inspection Contamination and Damage, Performing
  • Only applies to BEV
Vehicle from Below  
X -- Engine and Components in Engine Compartment (from Below), Visually Inspecting for Leaks and Damage
X -- Transmission, Final Drive and CV Boots, Checking for Leaks and Damage
X -- Front and Rear Brake Pad Thickness and Brake Rotor Condition, Checking
X -- Ball Joints, Axle Bearings, Coupling Rod and Stabilizer Bar Rubber Bushings, Visually Inspecting for Damage
X -- Tie Rods, Checking Play, Attachment and Ball Joint Boots
X -- Brake System and Shock Absorbers, Visually Inspecting for Leaks and Damage.
X -- Underbody, Visually Inspecting Underbody Protection, Underbody Trim Panels, Wire Routing and Plugs for Damage
X -- Front and Rear Coil Springs and Stop Buffers, Visually Inspecting for Damage
X -- Warning Label, Checking Presence
  • Only applies to BEV
X -- Removable Trailer Hitch, Checking
  • if equipped
Tires  
X -- Tire Pressure, Checking
X -- Tire Repair Kit, Checking for Damage and Use
X -- Tires, Checking Condition and Wear Pattern; Tread Depth, Entering
Front Compartment  
X -- 12V Battery, Checking
X -- Components in front compartment (from above): check for leaks and damage.
X -- Brake Fluid Level, Checking Depending on Brake Pad Wear
X -- Cooling System, Checking Freeze Protection and Coolant Level
X -- High-Voltage Components and High-Voltage Cables, Visually Inspecting for Damage, Correct Wire Routing and Attachment
  • Only applies to BEV
Final Procedures  
X -- Service Interval Display, Resetting
X -- Headlamps, Checking and Adjusting if Necessary
X -- Tire Pressure Monitoring System, Calibrating to Tire Pressure Adjustment
X -- Road Test, Performing
X -- High-Voltage Battery, Charging
  • Only applies to BEV
Chapter Navigation
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.