Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2021 Toyota 4Runner TRD Off-RoadFACTORY OEM SERVICE PROCEDURE
Dynamic Radar Cruise Control System
DYNAMIC RADAR CRUISE CONTROL SYSTEM DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION [08/2019 - 08/2021]
| DTC Code | Description |
|---|---|
| C1A02 | Vehicle Information Not Obtained |
| C1A0A | Front Radar Sensor Region Code Mismatch |
| C1A10 | Front Radar Sensor |
| C1A11 | Front Radar Sensor Incorrect Axial Gap |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted |
| C1A4A | Skid Control Buzzer Circuit |
| C1A52 | Radar Cruise Control Presence Determination Malfunction (Engine / HV) |
| P0571 | Brake Switch "A" Circuit |
| P0575 | Cruise Control Input Circuit |
| P1578 | Brake System |
| P1630 | Communication Error from VSC to ECM |
| P1631 | Communication Error from ECM to VSC |
| U0100 | Lost Communication with ECM / PCM "A" |
| U0104 | Lost Communication with Cruise Control Module |
| U0122 | Lost Communication with Vehicle Dynamics Control Module |
| U0125 | Lost Communication with Yaw Rate Sensor Module |
| U0126 | Lost Communication with Steering Angle Sensor Module |
| U0129 | Lost Communication with Brake System Control Module |
DYNAMIC RADAR CRUISE CONTROL SYSTEM DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION [08/2021 - 08/2022]
| DTC Code | Description |
|---|---|
| C1A02 | Vehicle Information Not Obtained |
| C1A0A | Front Radar Sensor Region Code Mismatch |
| C1A10 | Front Radar Sensor |
| C1A11 | Front Radar Sensor Incorrect Axial Gap |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted |
| C1A4A | Skid Control Buzzer Circuit |
| C1A52 | Radar Cruise Control Presence Determination Malfunction (Engine / HV) |
| P0571 | Brake Switch "A" Circuit |
| P0575 | Cruise Control Input Circuit |
| P1578 | Brake System |
| P1630 | Communication Error from VSC to ECM |
| P1631 | Communication Error from ECM to VSC |
| U0100 | Lost Communication with ECM / PCM "A" |
| U0104 | Lost Communication with Cruise Control Module |
| U0122 | Lost Communication with Vehicle Dynamics Control Module |
| U0125 | Lost Communication with Yaw Rate Sensor Module |
| U0126 | Lost Communication with Steering Angle Sensor Module |
| U0129 | Lost Communication with Brake System Control Module |
DYNAMIC RADAR CRUISE CONTROL SYSTEM DIAGNOSTIC TROUBLE CODE (DTC) IDENTIFICATION [08/2022 - ]
| DTC Code | Description |
|---|---|
| C1A02 | Vehicle Information Not Obtained |
| C1A0A | Front Radar Sensor Region Code Mismatch |
| C1A10 | Front Radar Sensor |
| C1A11 | Front Radar Sensor Incorrect Axial Gap |
| C1A14 | Front Radar Sensor Beam Axis Not Adjusted |
| C1A4A | Skid Control Buzzer Circuit |
| C1A52 | Radar Cruise Control Presence Determination Malfunction (Engine / HV) |
| P0571 | Brake Switch "A" Circuit |
| P0575 | Cruise Control Input Circuit |
| P1578 | Brake System |
| P1630 | Communication Error from VSC to ECM |
| P1631 | Communication Error from ECM to VSC |
| U0100 | Lost Communication with ECM / PCM "A" |
| U0104 | Lost Communication with Cruise Control Module |
| U0122 | Lost Communication with Vehicle Dynamics Control Module |
| U0125 | Lost Communication with Yaw Rate Sensor Module |
| U0126 | Lost Communication with Steering Angle Sensor Module |
| U0129 | Lost Communication with Brake System Control Module |
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
