Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
On-Vehicle Inspection
- PERFORM SPARK TEST
- Check for DTCs. Refer to DTC CHECK / CLEAR
.NOTE:
If any DTC is present, perform troubleshooting in accordance with the procedure for that DTC.
- Remove the ignition coils and spark plugs. Refer to REMOVAL .
- Disconnect the 4 fuel injector connectors.
- Set the vehicle to the inspection mode. Refer to INSPECTION MODE PROCEDURE . (step 3)
- Install the spark plug into the ignition coil, and then connect the ignition coil connector. (step 4)
- Ground the spark plug. (step 5)
- Check that spark occurs while the engine is being cranked. (step 6)NOTE:
- Be sure to ground the spark plugs when checking them.
- Do not crank the engine for more than 2 seconds.
- If a spark plug has been struck or dropped, replace it.
- If an ignition coil assembly has been struck or dropped, replace it.
HINT:
- Repeat steps 3 to 6 for each spark plug and ignition coil assembly.
- If spark does not occur for any cylinder, perform the following Inspect Ignition Coil and Spark Test procedure.
- Connect the 4 fuel injector connectors.
- Install the spark plugs and ignition coil assemblies. Refer to INSTALLATION .
- Check for DTCs. Refer to DTC CHECK / CLEAR .
- Clear the DTCs. Refer to DTC CHECK / CLEAR .
- Check for DTCs. Refer to DTC CHECK / CLEAR
.
- INSPECT IGNITION COIL AND SPARK TEST
- Check that the wire harness side connector of the ignition coil assembly is securely connected.
Result
Result Action NG Connect securely OK Go to next step - Perform a spark test on each ignition coil assembly.
- Replace the ignition coil assembly with a known good one.
- Set the vehicle to inspection mode. Refer to INSPECTION MODE PROCEDURE .
- Perform the spark test again.
Result
Result Action NG Go to next step OK Replace ignition coil
- Perform a spark test on each spark plug.
- Replace the spark plug with a known good one.
- Set the vehicle to inspection mode. Refer to INSPECTION MODE PROCEDURE .
- Perform the spark test again.
Result
Result Action NG Inspect the ignition system. Refer to DTC P0351: Ignition Coil "A" Primary / Secondary Circuit; DTC P0352: Ignition Coil "B" Primary / Secondary Circuit; DTC P0353: Ignition Coil "C" Primary / Secondary Circuit; DTC P0354: Ignition Coil "D" Primary / Secondary Circuit . OK Replace the spark plug NOTE:- If the ignition coil assembly has been struck or dropped, replace it.
- If the spark plug has been struck or dropped, replace it.
- Check that the wire harness side connector of the ignition coil assembly is securely connected.
- INSPECT SPARK PLUG
- Check the electrode.TEXT IN ILLUSTRATION
*1 Ground - Using a megohmmeter, measure the resistance.
Standard Resistance
10 MΩ or more
If the result is 10 MΩ or less, clean the plug and measure the resistance again.
HINT:
If a megohmmeter is not available, perform the following simple inspection instead.
- Using a megohmmeter, measure the resistance.
- Alternative inspection method:
- Quickly accelerate the engine to 4000 rpm 5 times.
- Remove each spark plug.
- Visually check the spark plug.
If the electrode is dry, the spark plug is functioning properly. If the electrode is damp, proceed to the next step.
- Check the spark plug for any damage to its threads and insulator.
If there is any damage, replace the spark plug.
RECOMMENDED SPARK PLUGManufacturer Spark Plug Type DENSO SC20HR11 - Check the spark plug electrode gap.TEXT IN ILLUSTRATION
*1 Spark Plug Electrode Gap Maximum Electrode Gap for Used Spark Plug
Electrode Gap 1.3 mm (0.0512 in.) If the gap is greater than the maximum, replace the spark plug.
Electrode Gap for New Spark Plug
Electrode Gap 1.0 to 1.1 mm (0.0394 to 0.0433 in.) - Clean the spark plugs.
If the electrode has traces of wet carbon, clean the electrode with a spark plug cleaner and then dry it.
Standard air pressure
588 kPa (6.0 kgf/cm2 , 85 psi)
Standard duration
20 seconds or less.
HINT:
Only use the spark plug cleaner when the electrode is free of oil. If the electrode has traces of oil, use gasoline to clean off the oil before using the spark plug cleaner.
- Check the electrode.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
