2012 Toyota Matrix Base, Automatic TransFACTORY OEM SERVICE PROCEDURE

Problem Symptoms Table

HINT:Β 

  • Use the table below to help determine the cause of the problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
POWER STEERING SYSTEM

Symptom Suspected Area See
Heavy steering Front tires (improperly inflated, unevenly worn) Refer to INSPECTION
Front wheel alignment (incorrect) Refer to ADJUSTMENT
Front suspension (lower ball joint) Refer to REMOVAL
Steering column Refer to REMOVAL
Torque sensor (built into steering column) Refer to DTC C1511: Torque Sensor Circuit Malfunction; DTC C1512: Torque Sensor Circuit Malfunction; DTC C1513: Torque Sensor Circuit Malfunction; DTC C1514: Torque Sensor Power Supply Abnormal; DTC C1517: Torque Hold Abnormal
Power steering motor Refer to REMOVAL
Speed sensor Refer to REMOVAL
Skid control ECU Refer to REMOVAL
Battery and power source system -
Power steering ECU power source voltage and relay Refer to TERMINALS OF ECUΒ 
Power steering ECU Refer to REMOVAL
Steering effort differs between right and left, or steering effort is uneven. Initialization of rotation angle sensor and calibration of torque sensor zero point are not completed. Refer to DTC C1515: Torque Sensor Zero Point Adjustment Undone; DTC C1525: Rotation Angle Sensor Initialization Undone
Front tires (improperly inflated, unevenly worn) Refer to INSPECTION
Front wheel alignment (incorrect) Refer to ADJUSTMENT
Front suspension (lower ball joint) Refer to REMOVAL
Power steering gear (for 2WD) Refer to REMOVAL
Power steering gear (for 4WD) Refer to REMOVAL
Torque sensor (built into steering column) Refer to DTC C1511: Torque Sensor Circuit Malfunction; DTC C1512: Torque Sensor Circuit Malfunction; DTC C1513: Torque Sensor Circuit Malfunction; DTC C1514: Torque Sensor Power Supply Abnormal; DTC C1517: Torque Hold Abnormal
Steering column Refer to REMOVAL
Power steering motor Refer to REMOVAL
Power steering ECU Refer to REMOVAL
While driving, steering effort does not change in accordance with vehicle speed or the steering wheel does not return properly. Front suspension (lower ball joint) Refer to REMOVAL
Speed sensor Refer to REMOVAL
Skid control ECU Refer to REMOVAL
Combination meter Refer to REMOVAL
Torque sensor (built into steering column) Refer to DTC C1511: Torque Sensor Circuit Malfunction; DTC C1512: Torque Sensor Circuit Malfunction; DTC C1513: Torque Sensor Circuit Malfunction; DTC C1514: Torque Sensor Power Supply Abnormal; DTC C1517: Torque Hold Abnormal
Power steering motor Refer to REMOVAL
Power steering ECU Refer to REMOVAL
CAN communication system Refer to HOW TO PROCEED WITH TROUBLESHOOTING
A knocking (or cranking) sound occurs when turning the steering wheel back and forth while power steering is in operation. Front suspension (lower ball joint) Refer to REMOVAL
Steering intermediate shaft Refer to REMOVAL
Power steering ECU Refer to REMOVAL
Noise occurs when turning the steering wheel during low-speed driving. Power steering gear (for 2WD) Refer to REMOVAL
Power steering gear (for 4WD) Refer to REMOVAL
Steering column Refer to REMOVAL
Friction occurs when turning the steering wheel during low-speed driving. Power steering motor Refer to REMOVAL
Steering column Refer to REMOVAL
A high-pitched sound (squeaking) occurs when turning the steering wheel slowly with the vehicle stopped. Power steering motor Refer to REMOVAL
The steering wheel vibrates and noise occurs when turning the steering wheel from lock to lock with the vehicle stopped. Power steering gear (for 2WD) Refer to REMOVAL
Power steering gear (for 4WD) Refer to REMOVAL
Steering column Refer to REMOVAL
P/S warning is always indicated on the combination meter. Power source voltage of power steering ECU Refer to TERMINALS OF ECUΒ 
Combination meter Refer to REMOVAL
Power steering ECU Refer to REMOVAL
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • β€’ You smell fuel, burning insulation, or see smoke.
  • β€’ Brakes feel soft, pull hard to one side, or make grinding noises.
  • β€’ The engine overheats, stalls repeatedly, or misfires under load.
  • β€’ You are missing required tools, torque specs, or safe lifting equipment.
  • β€’ You are not confident in the next step or safety outcome.