2011 Toyota RAV4 Base, 2.5 F, FWDFACTORY OEM SERVICE PROCEDURE

Problem Symptoms Table

HINT: 

  • Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.
  • Inspect the fuses and relays related to this system before inspecting the suspected areas below.
SFI SYSTEM

Symptom Suspected Area See
Engine does not crank (Does not start) Battery Refer to ON-VEHICLE INSPECTION - Step 1
Starter Refer to INSPECTION
Starter relay Refer to ON-VEHICLE INSPECTION - Step 1
Park/neutral position switch for 2WD Refer to INSPECTION - Step 1
Park/neutral position switch for 4WD Refer to INSPECTION - Step 1
Smart key system Refer to Engine does not Start
Cranking holding function circuit Refer to Cranking Holding Function Circuit
No initial combustion (Does not start) ECM power source circuit Refer to ECM Power Source Circuit
Crankshaft position sensor Refer to INSPECTION - Step 1
Camshaft position sensor Refer to DTC P0340: Camshaft Position Sensor Circuit Malfunction; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)
Ignition system Refer to ON-VEHICLE INSPECTION
Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel injector circuit Refer to Fuel Injector Circuit
Valve timing Refer to PROCEDURE - Step 5
VC output circuit Refer to VC Output Circuit
ECM Refer to TERMINALS OF ECM 
Engine cranks normally but difficult to start Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION - Step 1
Fuel injector circuit Refer to Fuel Injector Circuit
ECM power source circuit Refer to ECM Power Source Circuit
Engine coolant temperature sensor Refer to INSPECTION - Step 1
Air induction system Refer to ON-VEHICLE INSPECTION
Ignition system Refer to ON-VEHICLE INSPECTION
Spark plug Refer to ON-VEHICLE INSPECTION - Step 2
Throttle body Refer to INSPECTION - Step 1
Compression Refer to ON-VEHICLE INSPECTION - Step 4
Incomplete intermittent combustion occurs (Does not start) Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION - Step 1
Ignition circuit Refer to INSPECTION PROCEDURE
Ignition system Refer to ON-VEHICLE INSPECTION
Fuel injector circuit Refer to Fuel Injector Circuit
ECM power source circuit Refer to ECM Power Source Circuit
Crankshaft position sensor Refer to INSPECTION - Step 1
Camshaft position sensor Refer to DTC P0340: Camshaft Position Sensor Circuit Malfunction; DTC P0342: Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor); DTC P0343: Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)
Valve timing Refer to PROCEDURE - Step 5
High engine idle speed Throttle body Refer to INSPECTION PROCEDURE
Air induction system Refer to ON-VEHICLE INSPECTION
A/C signal circuit for Automatic Air Conditioning System Refer to TERMINALS OF ECU
A/C signal circuit for Manual Air Conditioning System Refer to TERMINALS OF ECU
ECM power source circuit Refer to ECM Power Source Circuit
Engine coolant temperature sensor Refer to INSPECTION - Step 1
PCV valve and hose Refer to INSPECTION - Step 1
Acoustic Control Induction System (ACIS) Refer to ACIS Control Circuit
Low engine idle speed (Poor idling) Throttle body Refer to INSPECTION - Step 1
A/C signal circuit for Automatic Air Conditioning System Refer to TERMINALS OF ECU
A/C signal circuit for Manual Air Conditioning System Refer to TERMINALS OF ECU
Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION - Step 1
Air induction system Refer to ON-VEHICLE INSPECTION
PCV valve and hose Refer to INSPECTION - Step 1
Acoustic Control Induction System (ACIS) Refer to ACIS Control Circuit
Rough idling Compression Refer to ON-VEHICLE INSPECTION - Step 4
Ignition system Refer to ON-VEHICLE INSPECTION
Spark plug Refer to ON-VEHICLE INSPECTION - Step 2
Fuel injector circuit Refer to Fuel Injector Circuit
ECM power source circuit Refer to ECM Power Source Circuit
Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION - Step 1
Throttle body Refer to INSPECTION - Step 1
Air induction system Refer to ON-VEHICLE INSPECTION
PCV valve and hose Refer to INSPECTION - Step 1
Air fuel ratio sensor Refer to INSPECTION - Step 1
Heated oxygen sensor Refer to INSPECTION - Step 1
Mass air flow meter Refer to ON-VEHICLE INSPECTION
Acoustic Control Induction System (ACIS) Refer to ACIS Control Circuit
Tumble Control Valve (TCV) Refer to ON-VEHICLE INSPECTION - Step 3
Idle hunting Throttle body Refer to INSPECTION - Step 1
Air induction system Refer to ON-VEHICLE INSPECTION
PCV valve and hose Refer to INSPECTION
Air fuel ratio sensor Refer to INSPECTION - Step 1
Mass air flow meter Refer to ON-VEHICLE INSPECTION
Acoustic Control Induction System (ACIS) Refer to ACIS Control Circuit
Tumble Control Valve (TCV) Refer to ON-VEHICLE INSPECTION - Step 3
Hesitation/poor acceleration Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION
Spark plug Refer to ON-VEHICLE INSPECTION - Step 2
Ignition system Refer to ON-VEHICLE INSPECTION
Fuel injector circuit Refer to Fuel Injector Circuit
ECM power source circuit Refer to ECM Power Source Circuit
Mass air flow meter Refer to ON-VEHICLE INSPECTION
Throttle body Refer to INSPECTION - Step 1
Air induction system Refer to ON-VEHICLE INSPECTION
Valve timing Refer to PROCEDURE - Step 5
Compression Refer to ON-VEHICLE INSPECTION - Step 4
Brake override system Refer to Brake Override System
Surging (Poor driveability) Spark plug Refer to ON-VEHICLE INSPECTION - Step 2
Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION - Step 1
Ignition system Refer to ON-VEHICLE INSPECTION
Fuel injector circuit Refer to Fuel Injector Circuit
ECM power source circuit Refer to ECM Power Source Circuit
Mass air flow meter Refer to ON-VEHICLE INSPECTION
Variable valve timing (VVT) system Refer to INSPECTION PROCEDURE
Compression Refer to ON-VEHICLE INSPECTION - Step 4
Engine stalls soon after starting Fuel pump control circuit Refer to Fuel Pump Control Circuit
Fuel pump Refer to INSPECTION - Step 1
Spark plug Refer to ON-VEHICLE INSPECTION - Step 2
Ignition system Refer to ON-VEHICLE INSPECTION
Fuel injector circuit Refer to Fuel Injector Circuit
ECM power source circuit Refer to ECM Power Source Circuit
Mass air flow meter Refer to ON-VEHICLE INSPECTION
Variable valve timing (VVT) system Refer to INSPECTION PROCEDURE
Throttle body Refer to INSPECTION - Step 1
Air induction system Refer to ON-VEHICLE INSPECTION
PCV valve and hose Refer to INSPECTION - Step 1
Compression Refer to ON-VEHICLE INSPECTION - Step 4
Engine stalls only during A/C operation A/C signal circuit for Automatic Air Conditioning System Refer to TERMINALS OF ECU
A/C signal circuit for Manual Air Conditioning System Refer to TERMINALS OF ECU
ECM Refer to TERMINALS OF ECM 
Unable/difficult to refuel Refueling valve (canister) -
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.