Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
How To Proceed With Troubleshooting
HINT:Â
*: Use the Techstream.
- VEHICLE BROUGHT TO WORKSHOPÂ
NEXT: Go to next stepÂ
- CUSTOMER PROBLEM ANALYSISÂ
NEXT: Go to next stepÂ
- CONNECT TECHSTREAM TO DLC3*Â
HINT:Â
If the display indicates a communication fault in the Techstream, inspect the DLC3. When any CAN communication system DTCs are output, perform troubleshooting on the CAN communication system first.
NEXT: Go to next stepÂ
- CHECK DTC AND FREEZE FRAME DATA*Â
HINT:Â
Record or print DTCs and freeze frame data, if necessary.
NEXT: Go to next stepÂ
- CLEAR DTC AND FREEZE FRAME DATA*Â
NEXT: Go to next stepÂ
- CONDUCT VISUAL INSPECTIONÂ
NEXT: Go to next stepÂ
- SET CHECK MODE DIAGNOSIS*Â
HINT:Â
Refer to Check Mode Procedure. Refer to CHECK MODE PROCEDUREÂ
NEXT: Go to next stepÂ
- CONFIRM PROBLEM SYMPTOMSÂ
HINT:Â
If the engine does not start, perform steps 10 and 12 first.
Result
Result Proceed to Malfunction does not occur A Malfunction occurs B B → GO TO STEP  10Â
A: Go to next stepÂ
- SIMULATE SYMPTOMSÂ
HINT:Â
Refer to Problem Symptoms Table. Refer to PROBLEM SYMPTOMS TABLEÂ
NEXT: Go to next stepÂ
- CHECK FOR DTCS*Â
HINT:Â
Refer to DTC Check / Clear. Refer to DTC CHECK / CLEARÂ
Result
Result Proceed to Trouble code A No code B B → GO TO STEP  12Â
A: Go to next stepÂ
- REFER TO Â DIAGNOSTIC TROUBLE CODE CHARTÂ Â DTC CHARTÂ
HINT:Â
Refer to Diagnostic Trouble Code Chart. Refer to DIAGNOSTIC TROUBLE CODE CHARTÂ
NEXT: Go to next stepÂ
- CONDUCT BASIC INSPECTIONÂ
Result
Result Proceed to Malfunctioning parts not confirmed A Malfunctioning parts confirmed B B → GO TO STEP  17Â
A: Go to next stepÂ
- REFER TO PROBLEM SYMPTOMS TABLEÂ
HINT:Â
Refer to Problem Symptoms Table. Refer to PROBLEM SYMPTOMS TABLEÂ
Result
Result Proceed to Malfunctioning circuit confirmed A Malfunctioning parts confirmed B B → GO TO STEP  17Â
A: Go to next stepÂ
- CHECK ECM POWER SOURCE CIRCUITÂ
HINT:Â
Refer to ECM Power Source Circuit. Refer to ECM Power Source Circuit
NEXT: Go to next stepÂ
- CONDUCT CIRCUIT INSPECTIONÂ
Result
Result Proceed to Malfunction not confirmed A Malfunction confirmed B B → GO TO STEP  18Â
A: Go to next stepÂ
- CHECK FOR INTERMITTENT PROBLEMSÂ
NEXT: Go to next stepÂ
- CONDUCT PARTS INSPECTIONÂ
NEXT: Go to next stepÂ
- IDENTIFY PROBLEMÂ
NEXT: Go to next stepÂ
- ADJUST AND/OR REPAIRÂ
NEXT: Go to next stepÂ
- CONDUCT CONFIRMATION TESTÂ
NEXT → ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
