2011 Toyota 4Runner TrailFACTORY OEM SERVICE PROCEDURE

Terminals Of Ecu

  1. CHECK 4WD CONTROL ECU 
    Fig 1: Identifying 4WD Control ECU Connector Terminal Identification
    GTY232020Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    1. Measure the voltage and resistance according to the value(s) in the table below.
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      F47-2 (4WDL) - F46-4 (GND) L - W-B Transfer indicator switch (L4 position) Ignition switch ON
      Transfer shift lever position H2 or H4
      10.5 to 14 V
      Ignition switch ON
      Transfer shift lever position L4 or N
      Below 1.5 V
      F47-3 (4WD) - F46-4 (GND) B - W-B Transfer indicator switch (4WD position) Ignition switch ON
      Transfer shift lever position H2
      10.5 to 14 V
      Ignition switch ON
      Transfer shift lever position H4, L4 or N
      Below 1.5 V
      F47-9 (DL1) - F46-4 (GND) LG - W-B A.D.D. actuator limit switch Ignition switch ON
      Transfer shift lever position H2
      Below 1.5 V
      Ignition switch ON
      Transfer shift lever position H4, L4 or N
      10.5 to 14 V
      F47-10 (DL2) - F46-4 (GND) GR - W-B A.D.D. actuator limit switch Ignition switch ON
      Transfer shift lever position H2
      10.5 to 14 V
      Ignition switch ON
      Transfer shift lever position H4, L4 or N
      Below 1.5 V
      F47-15 (ADD) - F46-4 (GND) W - W-B A.D.D. detection switch Ignition switch ON
      Transfer shift lever position H2
      9.5 to 14 V
      Ignition switch ON
      Transfer shift lever position H4, L4 or N
      Below 1.5 V
      F47-16 (NP) - F46-4 (GND) R - W-B Transfer indicator switch (Neutral position) Ignition switch ON
      Transfer shift lever position N
      Below 1.5 V
      Ignition switch ON
      Transfer shift lever position not N
      10.5 to 14 V
      F47-19 (CANH) - F46-4 (GND) G - W-B CAN communication line Ignition switch ON Pulse generation (SeeFig 2 )
      F47-20 (CANL) - F46-4 (GND) W - W-B CAN communication line Ignition switch ON Pulse generation (See Fig 3 )
      F47-21 (L4) - F46-4 (GND) R - W-B Transfer L4 signal Ignition switch ON
      Transfer shift lever position H2 or H4
      10 to 14 V
      Ignition switch ON
      Transfer shift lever position L4 or N
      Below 1.5 V
      F46-1 (DM1) - F46-4 (GND) B - W-B A.D.D. actuator motor Ignition switch ON
      Transfer shift lever position H2 → H4, L4 or N (During operation of A.D.D. actuator motor from FREE to LOCK)
      10 to 14 V
      Ignition switch ON
      Transfer shift lever position H2 → H4, L4 or N (A.D.D. actuator motor stopped)
      Below 1.5 V
      F46-3 (IG) - F46-4 (GND) R - W-B IG power Ignition switch ON 11 to 14 V
      F46-4 (GND) - Body ground W-B - Body ground Ground Always Below 1 Ω
      F46-5 (DM2) - F46-4 (GND) Y - W-B A.D.D. actuator motor Ignition switch ON
      Transfer shift lever position H4, L4 or N → H2 (During operation of A.D.D. actuator motor from LOCK to FREE)
      10 to 14 V
      Ignition switch ON
      Transfer shift lever position H4, L4 or N → H2 (A.D.D. actuator motor stopped)
      Below 1.5 V
    2. Using an oscilloscope, check waveform 1.
      Fig 2: Identifying Waveform 1
      GTY218411Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      WAVEFORM 1 (REFERENCE)

      Item Content
      Terminal No. (Symbols) F47-19 (CANH) - F46-4 (GND)
      Tool setting 1 V/DIV., 10 μsec./DIV.
      Condition Engine stopped and ignition switch ON
      TEXT IN ILLUSTRATION

      *1 Waveform 1

      HINT: 

      The waveform varies depending on the CAN communication signal.

    3. Using an oscilloscope, check waveform 2.
      Fig 3: Identifying Waveform 2
      GTY213004Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      WAVEFORM 2 (REFERENCE)

      Item Content
      Terminal No. (Symbols) F47-20 (CANL) - F46-4 (GND)
      Tool setting 1 V/DIV., 10 μsec./DIV.
      Condition Engine stopped and ignition switch ON
      TEXT IN ILLUSTRATION

      *1 Waveform 2

      HINT: 

      The waveform varies depending on the CAN communication signal.

Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.