Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
How To Proceed With Troubleshooting
HINT:Â
*: Use the Techstream.
- VEHICLE BROUGHT TO WORKSHOPÂ
NEXT: Go to next stepÂ
- CUSTOMER PROBLEM ANALYSISÂ
NEXT: Go to next stepÂ
- CONNECT TECHSTREAM TO DLC3*Â
HINT:Â
If the display indicates a communication fault in the Techstream, inspect the DLC3.
NEXT: Go to next stepÂ
- CHECK DTC AND FREEZE FRAME DATA*Â
HINT:Â
If necessary, record or print DTCs and freeze frame data.
- Check DTC, refer to DTC CHECK / CLEARÂ .
- Check Freeze Frame Data, refer to FREEZE FRAME DATAÂ .
NEXT: Go to next stepÂ
- CLEAR DTC AND FREEZE FRAME DATA*Â
- Clear DTC, refer to DTC CHECK / CLEARÂ .
- Clear Freeze Frame Data, refer to FREEZE FRAME DATAÂ .
NEXT: Go to next stepÂ
- CONDUCT VISUAL INSPECTIONÂ
NEXT: Go to next stepÂ
- SET CHECK MODE DIAGNOSIS*Â
- Refer to Check Mode Procedure, refer to CHECK MODE PROCEDUREÂ .
NEXT: Go to next stepÂ
- Refer to Check Mode Procedure, refer to CHECK MODE PROCEDUREÂ .
- CONFIRM PROBLEM SYMPTOMSÂ
HINT:Â
If the engine does not start, first perform the "Check DTC" procedures and "Conduct Basic Inspection" procedures below.
Result Proceed to Malfunction does not occur A Malfunction occurs B B → GO TO   10 STEP 10Â
A: Go to next stepÂ
- SIMULATE SYMPTOMSÂ
NEXT: Go to next stepÂ
- CHECK FOR DTC*Â
- Refer to DTC Check / Clear, refer to DTC CHECK / CLEARÂ .
Result Proceed to Trouble code output A No code output B B → GO TO   12 STEP 12Â
A: Go to next stepÂ
- Refer to DTC Check / Clear, refer to DTC CHECK / CLEARÂ .
- REFER TO DTC CHARTÂ
- Refer to Diagnostic Trouble Code Chart, refer to DIAGNOSTIC TROUBLE CODE CHARTÂ .
NEXT → GO TO   14 STEP 14Â
- Refer to Diagnostic Trouble Code Chart, refer to DIAGNOSTIC TROUBLE CODE CHARTÂ .
- CONDUCT BASIC INSPECTIONÂ
- Refer to Basic Inspection, refer to BASIC INSPECTIONÂ .
Result Proceed to Malfunctioning parts not confirmed A Malfunctioning parts confirmed B B → GO TO   17 STEP 17Â
A: Go to next stepÂ
- Refer to Basic Inspection, refer to BASIC INSPECTIONÂ .
- REFER TO PROBLEM SYMPTOMS TABLEÂ
- Refer to Problem Symptoms Table, refer to PROBLEM SYMPTOMS TABLEÂ .
Result Proceed to Malfunctioning circuit confirmed A Malfunctioning parts confirmed B B → GO TO STEP 17Â
A: Go to next stepÂ
- Refer to Problem Symptoms Table, refer to PROBLEM SYMPTOMS TABLEÂ .
- CHECK ECM POWER SOURCE CIRCUITÂ
- Refer to ECM Power Source Circuit, refer to ECM Power Source Circuit
.
NEXT: Go to next stepÂ
- Refer to ECM Power Source Circuit, refer to ECM Power Source Circuit
.
- CONDUCT CIRCUIT INSPECTIONÂ
Result Proceed to Malfunction not confirmed A Malfunction confirmed B B → GO TO STEP 18Â
A: Go to next stepÂ
- CHECK FOR INTERMITTENT PROBLEMSÂ
- Refer to Check for Intermittent Problems, refer to CHECK FOR INTERMITTENT PROBLEMSÂ .
NEXT → GO TO STEP 18Â
- Refer to Check for Intermittent Problems, refer to CHECK FOR INTERMITTENT PROBLEMSÂ .
- CONDUCT PARTS INSPECTIONÂ
NEXT: Go to next stepÂ
- IDENTIFY PROBLEMÂ
NEXT: Go to next stepÂ
- ADJUST AND/OR REPAIRÂ
NEXT: Go to next stepÂ
- CONDUCT CONFIRMATION TESTÂ
NEXT → ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
