2011 Toyota 4Runner Limited, RWDFACTORY OEM SERVICE PROCEDURE

Service Data

Camshaft Timing Oil Control Valve

Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.9 to 7.9 Ω

Crankshaft Position Sensor

Tester Connection Condition Specified Condition
1 - 2 Cold 1630 to 2740 Ω
Hot 2065 to 3225 Ω

Engine Coolant Temperature Sensor

Tester Connection Condition Specified Condition
1 - 2 Approx. 20°C (68°F) 2.32 to 2.59 kΩ
Approx. 80°C (176°F) 0.310 to 0.326 kΩ

Throttle Body

Tester Connection Condition Specified Condition
2 (M+) - 1 (M-) 20°C (68°F) 0.3 to 100 Ω

Knock Sensor

Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 120 to 280 kΩ

Accelerator Pedal

Accelerator Pedal Operation Accelerator Position No. 1 Accelerator Position No. 2
Released 0.5 to 1.1 V 1.2 to 2.0 V
Depressed 2.6 to 4.5 V 3.4 to 5.3 V

Air Fuel Ratio Sensor (for Bank 1)

Tester Connection Condition Specified Condition
1 (HA1A) - 2 (+B) 20°C (68°F) 1.8 to 3.4 Ω
1 (HA1A) - 4 (A1A-) Always 10 kΩ or higher

Air Fuel Ratio Sensor (for Bank 2)

Tester Connection Condition Specified Condition
1 (HA2A) - 2 (+B) 20°C (68°F) 1.8 to 3.4 Ω
1 (HA2A) - 4 (A2A-) Always 10 kΩ or higher

Heated Oxygen Sensor (for Bank 1)

Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT1B) - 4 (E2) Always 10 kΩ or higher

Heated Oxygen Sensor (for Bank 2)

Tester Connection Condition Specified Condition
1 (HT2B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT2B) - 4 (E2) Always 10 kΩ or higher

Circuit Opening Relay

Tester Connection Condition Specified Condition
3 - 5 Battery voltage is not applied to terminals 1 and 2 10 kΩ or higher
Battery voltage is applied to terminals 1 and 2 Below 1 Ω

No. 1 Integration Relay (IG2)

Tester Connection Condition Specified Condition
IG2 fuse Always Below 1 Ω
1E-1 - 1C-4 Battery voltage not applied to terminals 1C- 1 and 1C-3 10 kΩ or higher
Battery voltage applied to terminals 1C-1 and 1C-3 Below 1 Ω

No. 1 Integration Relay (EFI)

Tester Connection Condition Specified Condition
EFI fuse Always Below 1 Ω
1E-1 - 1D-4 Battery voltage not applied to terminals 1D- 2 and 1D-3 10 kΩ or higher
Battery voltage applied to terminals 1D-2 and 1D-3 Below 1 Ω

No. 1 Integration Relay (A/F)

Tester Connection Condition Specified Condition
A/F fuse Always Below 1 Ω
1E-1 - 1D-8 Battery voltage not applied to terminals 1D- 4 and 1D-7 10 kΩ or higher
Battery voltage applied to terminals 1D-4 and 1D-7 Below 1 Ω

Main Body ECU (Driver Side Junction Block) for ACC Relay

Tester Connection Condition Specified Condition
2B-17 - 2E-1 Battery voltage not applied to terminals 2C- 48 and 2B-4 10 kΩ or higher
Battery voltage applied to terminals 2C-48 and 2B-4 Below 1 Ω

Main Body ECU (Driver Side Junction Block) for IG1 No. 2 Relay

Tester Connection Condition Specified Condition
2C-31 - 2E-1 Battery voltage not applied to terminals 2C- 52 and 2B-4 10 kΩ or higher
Battery voltage applied to terminals 2C-52 and 2B-4 Below 1 Ω

Spark Plug

Recommended spark plug Correct electrode gap for new spark plug Maximum electrode gap for used spark plug Standard insulation resistance
SK20HR11 Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.) 1.3 mm (0.0512 in.) 10 MΩ or higher
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.