2010 Toyota Matrix XRS, AutomaticFACTORY OEM SERVICE PROCEDURE

Service Data

Spark plug Standard resistance 10 MΩ or more
Recommended spark plug SK20R11 DENSO made
IFR6A11 NGK made
Electrode gap 1.0 to 1.1 mm (0.0394 to 0.0433 in.)
Maximum electrode gap 1.3 mm (0.0512 in.) for used plug
Camshaft oil control valve 1 - 2 Resistance:
6.9 to 7.9 Ω at 20°C (68°F)
Throttle body 1 (M-) - 2 (M+) Resistance:
0.3 to 100 Ω at 20°C (68°F)
Accelerator pedal Accelerator position No. 1 standard voltage Accelerator pedal is released 0.5 to 1.1 V
Accelerator pedal is depressed 2.6 to 4.5 V
Accelerator position No. 2 standard voltage Accelerator pedal is released 1.2 to 2.0 V
Accelerator pedal is depressed 3.4 to 5.0 V
Mass air flow meter Engine not running
30 seconds after ignition switch is turned to ON		 Less than 0.48 g/sec.
1 (THA) - 2 (E2) Resistance:
13.6 to 18.4 kΩ at -20°C (-4°F)
2.21 to 2.69 kΩ at 20°C (68°F)
0.493 to 0.667 kΩ at 60°C (140°F)
Camshaft position sensor 1 - 2 Resistance:
835 to 1400 Ω at -10 to 50°C (14 to 122°F)
1060 to 1645 Ω at 50 to 100°C (122 to 212°F)
Crankshaft position sensor 1 - 2 Resistance:
985 to 1600 Ω at -10 to 50°C (14 to 122°F)
1265 to 1890 Ω at 50 to 100°C (122 to 212°F)
Engine coolant temperature sensor 1 - 2 Resistance:
2.32 to 2.59 kΩ at 20°C (68°F)
0.310 to 0.326 kΩ at 80°C (176°F)
Knock sensor 1 - 2 Resistance:
120 to 280 kΩ
Always
Air fuel ratio sensor (HT) - (+B) Resistance:
1.8 to 3.4 Ω at 20°C (68°F)
(HT) - (AF-) Resistance:
10 kΩ or higher
Heated oxygen sensor (HT) - (+B) Resistance:
11 to 16 Ω at 20°C (68°F)
(HT) - (E) Resistance:
10 kΩ or higher
Integration relay
(EFI MAIN RELAY)		 1E-1 - 1B-4 Resistance:
10 kΩ or higher
(Battery voltage is not applied between terminals 1B-3 and 1B-2)
Resistance:
Below 1 Ω
(Battery voltage is applied between terminals 1B-3 and 1B-2)
Integration relay
(IG2 RELAY)		 1E-1 - 1A-4 Resistance:
10 kΩ or higher
(Battery voltage is not applied between terminals 1A-2 and 1A-3)
Resistance:
Below 1 Ω
(Battery voltage is applied between terminals 1A-2 and 1A-3)
Integration relay
(HORN RELAY)		 1E-1 - 1A-8 Resistance:
10 kΩ or higher
(Battery voltage is not applied between terminals 1A-6 and 1A-7)
Resistance:
Below 1 Ω
(Battery voltage is applied between terminals 1A-6 and 1A-7)
Circuit opening relay 2A-8 - 2B-11 Resistance:
10 kΩ or higher
(Battery voltage is not applied between terminals 2B-10 and 2B-9)
Resistance:
Below 1 Ω
(Battery voltage is applied between terminals 2B-10 and 2B-9)
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.