Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Toyota Sienna CEFACTORY OEM SERVICE PROCEDURE
Freeze Frame Data
- FREEZE FRAME DATAΒ
- The vehicle (sensor) status, stored during ABS and/ or VSC operation or at the time of an error code detection, can be displayed by Techstream.
- Only one record of freeze frame data is stored and the freeze frame data generated during ABS and/or VSC operation are updated whenever the vehicle status is changed. Also, the number of the ignition switch is ON after the freeze frame data is stored can be stored up to 31 and it can be displayed. After storing the DTC, the freeze frame data is not updated.
HINT:
If the ignition switch "ON" operation exceeds 31 times, "31 "appears on the display.
- If a malfunction occurs, the freeze frame data is stored but the ABS actuation data is deleted.FREEZE FRAME DATA REFERENCE VALUE CHART
Tester Display Measurement Item Reference Value Elapsed Time after Freeze Trigger Elapsed time after freeze trigger Min.: 0 ms, Max.: 500 ms Number of IG ON Number of operations of ignition switch ON after memorizing freeze frame data 0 to 31 Buzzer Skid buzzer signal Skid control buzzer ON: ON, OFF: OFF Stop Lamp SW Stop light switch signal Stop light switch ON: ON, OFF: OFF Parking Brake SW Parking brake switch signal Parking brake switch ON: ON, OFF: OFF TRC (TRAC)/VSC OFF SW(1) Traction OFF switch signal TRAC OFF SW ON: ON
OFF: OFFGear Position Gear position information FAIL
1st
2nd
3rd
4th
5th
6th
7th
8th
P,N
R
NOT RShift Lever Position Shift lever position FAIL
P,N
R
D/M
6th/B
5th
4th
3rd
2nd
1stOperated System System status ABS activated: ABS
VSC activated: VSC
TRAC activated: TRAC
BA activated: BA
Fail safe mode activated: FAIL
No system activated: NON
System prohibited: SYSMaster Cylinder Sensor Master cylinder pressure sensor reading Brake pedal release: 0.3 to 0.9 V
Brake pedal depress: 0.8 to 4.5 VM/C Sensor Grade Master cylinder pressure sensor change Min.: -30 MPa/s
Max.: 225 MPa/sYaw Rate Sensor Yaw rate angle sensor reading Min.: -128 deg/s, Max.: 127 deg/s Lateral G Lateral G Min.: -25.11 m/s2 , Max.: 24.91 m/s2 Forward and Rearward G Forward and backward G Min.: -25.11 m/s2 , Max.: 24.91 m/s2 FR Wheel Speed FR wheel speed Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) FL Wheel Speed FL wheel speed Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) RR Wheel Speed RR wheel speed Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) RL Wheel Speed RL wheel speed Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle Speed Wheel speed sensor reading Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle Speed Grade Vehicle speed grade Min.: -25.11 m/s2 , Max.: 24.91 m/s2 Real Engine Torque Real engine torque Min,: -1.024 Nm, Max.: 1.023 Nm Accelerator Opening Angle % Accelerator opening angle % Min.: 0 %, Max.: 128 % Inspection Mode Inspection mode OTHER: Normal, INSPECT: Service Steering Angle Sensor Steering sensor reading Left turn: Increase
Right turn: Drop(1) 2WD
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- β’ You smell fuel, burning insulation, or see smoke.
- β’ Brakes feel soft, pull hard to one side, or make grinding noises.
- β’ The engine overheats, stalls repeatedly, or misfires under load.
- β’ You are missing required tools, torque specs, or safe lifting equipment.
- β’ You are not confident in the next step or safety outcome.
