Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Toyota Sienna CEFACTORY OEM SERVICE PROCEDURE
Vehicle Stability Control System: Calibration
- CLEAR ZERO POINT CALIBRATION (WHEN USING TECHSTREAM):
- Connect Techstream to the DLC3.
- Turn the ignition switch to the ON position.
- Operate Techstream to erase the codes (select "Reset Memory").
HINT:
Refer to the Techstream operator's manual for further details.
- Using Techstream, perform zero point calibration of the yaw rate and deceleration sensor.
- PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR (WHEN USING TECHSTREAM): NOTE:
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it in a stationary condition. (Do not turn the ignition switch to the ON position.)
- Be sure to do this on a level surface (with an inclination of less than 1 %).
- Procedures for test mode.
- Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position and apply the parking brake.
- Connect Techstream to the DLC3.
- Turn the ignition switch to the ON position.
- Set Techstream to test mode (select "Test Mode").
HINT:
Refer to the Techstream operator's manual for further details.
- Obtain the zero point of the yaw rate and deceleration sensor.
- Keep the vehicle in the stationary condition on a level surface for 2 seconds or more.
- Check that the ABS warning light and VSC warning light blink.
HINT:
- If the ABS warning light and VSC warning light do not blink perform zero point calibration again.
- The zero point calibration is performed only once after the system enters the test mode.
- Calibration cannot be performed again until the stored data is cleared once.
- Turn the ignition switch off and disconnect Techstream.
- PERFORM ZERO POINT CALIBRATION OF YAW RATE AND DECELERATION SENSOR (WHEN USING SST CHECK WIRE): NOTE:
- While obtaining the zero point, do not vibrate the vehicle by tilting, moving or shaking it and keep it in a stationary condition. (Do not turn the ignition switch to the ON position.)
- Be sure to do this on a level surface (with an inclination of less than 1 %).
- Clear the zero point calibration.
- Turn the ignition switch to the ON position.
- Using SST, connect and disconnect terminals TS and CG of the DLC3 4 times or more within 8 seconds.
SST 09843-18040
- Procedures for test mode.
- Turn the ignition switch off.
- Using SST, connect terminals TS and CG of the DLC3.
SST 09843-18040
- Check that the steering wheel is in the straight-ahead position and move the shift lever to the P position.
- Obtain the zero point of the yaw rate and deceleration sensor.
- Turn the ignition switch to the ON position.
- Keep the vehicle in a stationary condition on a level surface for 2 seconds or more.
- Check that the ABS warning light and VSC light blink (test mode).
HINT:
- If the ABS warning light and VSC warning light do not blink perform zero point calibration again.
- The zero point calibration is performed only once after the system enters the test mode.
- Calibration cannot be performed again until the stored data is cleared once.
- Turn the ignition switch off and disconnect the SST from the DLC3.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
