Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- INSPECT FUSE (AM2, GAUGE, FR DOOR, ECU-IG)Â
- Remove the AM2 fuse from the engine room junction block.
- Remove the GAUGE, FR DOOR and ECU-IG fuses from the driver side junction block.
- Measure the resistance of the fuses.
Standard resistance:Â
Below 1 ΩÂ
NG : REPLACE FUSEÂ
OK : GO TO NEXT STEPÂ
- INSPECT IG1 RELAYÂ
- Remove the IG1 relay from the driver side junction block.
- Measure the resistance of the relay.
Standard resistanceÂ
TERMINALS RESISTANCE SPECIFICATIONTester Connection Specified Condition 3 - 5 10 kΩ or higher 3 - 5 Below 1 Ω (when battery voltage is applied to terminals 1 and 2)
NG : REPLACE IG1 RELAYÂ
OK : GO TO NEXT STEPÂ
- CHECK WIRE HARNESS (MASTER SWITCH - BATTERY AND BODY GROUND)Â
- Disconnect the P17 switch connector.
- Measure the voltage or resistance of the wire harness side connector.
Standard voltageÂ
TERMINALS VOLTAGE SPECIFICATIONTester Connection Condition Specified Condition P17-6 (B) - Body ground Power switch ON (IG) 10 to 14 V P17-7 (BW) - Body ground Always 10 to 14 V P17-11 (BDR) - Body ground Power switch ON (IG) 10 to 14 V Standard resistanceÂ
TERMINALS RESISTANCE SPECIFICATIONTester Connection Condition Specified Condition P17-1 (E) - Body ground Always Below 1 Ω
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
OK : REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLYÂ
NG : GO TO NEXT STEPÂ
- CHECK WIRE HARNESS (MASTER SWITCH - JUNCTION BLOCK)Â
- Disconnect the P17 switch connector.
- Disconnect the 1G and 1H junction block connectors.
- Measure the resistance of the wire harness side connectors.
Standard resistanceÂ
TERMINALS RESISTANCE SPECIFICATIONTester Connection Specified Condition P17-11 (BDR) - 1G-6 Below 1 Ω P17-7 (BW) - 1H-10 Below 1 Ω P17-6 (B) - 1H-11 Below 1 Ω P17-11 (BDR) or 1G-6 - Body ground 10 kΩ or higher P17-7 (BW) or 1H-10 - Body ground 10 kΩ or higher P17-6 (B) or 1H-11 - Body ground 10 kΩ or higher
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NG : REPAIR OR REPLACE HARNESS AND CONNECTORÂ
OK : GO TO NEXT STEPÂ
- CHECK WIRE HARNESS (JUNCTION BLOCK - BODY GROUND)Â
- Disconnect the 1B and 1E junction block connectors.
- Measure the voltage and resistance of the wire harness side connectors.
Standard voltageÂ
TERMINALS VOLTAGE SPECIFICATIONTester Connection Specified Condition 1B-1 - Body ground 10 to 14 V Standard resistanceÂ
TERMINALS RESISTANCE SPECIFICATIONTester Connection Specified Condition 1E-17 - Body ground Below 1 Ω
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NG : REPAIR OR REPLACE HARNESS AND CONNECTORÂ
OK : GO TO NEXT STEPÂ
- CHECK BASIC FUNCTION OF PUSH BUTTON START SYSTEMÂ
- Check that the push button start system operates normally.
OK : Push button start system operates normally.Â
NG : GO TO PUSH BUTTON START SYSTEMÂ
OK : REPLACE DRIVER SIDE JUNCTION BLOCK ASSEMBLYÂ
- Check that the push button start system operates normally.
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
