Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2009 Toyota Matrix Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Fuel Pump: Removal
- REMOVE REAR SEAT CUSHION ASSEMBLY (See REMOVAL )
- REMOVE REAR FLOOR SERVICE HOLE COVER
- Remove the rear floor service hole cover.
- Disconnect the connector from the fuel suction tube assembly.
- DISCHARGE FUEL SYSTEM PRESSURE
- Discharge fuel system pressure (See FUEL SYSTEM ).
- DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
- DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
- Remove the tube joint clip, then pull the fuel tube joint out of the plug of the fuel suction tube assembly.NOTE:
- Check that there is no dirt or other foreign objects around the fuel tube joint before disconnecting it. Clean the joint if necessary.
- It is necessary to prevent mud or dirt from entering the joint. If mud or dirt gets in the joint, the O-rings may not seal properly.
- Only disconnect the joint by hand.
- Do not bend, kink or twist the nylon tubes.
- Protect the contact surfaces by covering it with a plastic bag.
- Remove the tube joint clip, then pull the fuel tube joint out of the plug of the fuel suction tube assembly.
- DISCONNECT FUEL TANK VENT HOSE
- Disconnect the fuel tank vent hose.
- Pinch the retainer and pull the fuel tank vent connector out of the fuel tank to disconnect the fuel tank vent hose from the fuel suction plate.NOTE:
- Check that there is no dirt or other foreign objects around the connector before disconnecting it. Clean the connector if necessary.
- It is necessary to prevent mud or dirt from entering the connector. If mud or dirt gets in the connector, the O-rings may not seal properly.
- Only disconnect the quick connector by hand.
- Do not bend, kink or twist the nylon tubes.
- Protect the connector by covering it with a plastic bag.
- If the pipe and connector are stuck, carefully try wiggling or pushing and pulling on the connector to release it. Pull the connector off the pipe carefully.
- Pinch the retainer and pull the fuel tank vent connector out of the fuel tank to disconnect the fuel tank vent hose from the fuel suction plate.
- Disconnect the fuel tank vent hose.
- REMOVE FUEL PUMP GAUGE RETAINER
- Using a 6 mm socket hexagon wrench, set SST to the fuel pump gauge retainer.
SST 09808-14020 (09808-01410, 09808-01420, 09808-01430)
HINT:
- Engage the SST claws securely with the fuel pump gauge retainer ribs to secure SST.
- Install SST while pressing the SST claws toward the fuel pump gauge retainer (toward the center of SST).
- Using SST, loosen the fuel pump gauge retainer.
SST 09808-14020 (09808-01410, 09808-01420, 09808-01430)
NOTE:- Do not use any tools other than specified in this operation. Damage to the fuel pump gauge retainer or the fuel tank may result.
- Loosen the retainer by turning it counterclockwise while holding SST down. Do not allow the claw of the tank suction tube support to slip out of its groove on the fuel tank.
- Using a 6 mm socket hexagon wrench, set SST to the fuel pump gauge retainer.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
