Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Steering Column Assembly: Installation
- INSTALL STEERING COLUMN HOLE COVER
- Install the steering column hole cover to the main shaft LWR dust cover.
- Install the steering column hole cover sub-assembly with the nut and 2 bolts.
Torque: 5.0 N*m (51 kgf*cm, 44 in.*lbf)
- INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY
- Install the steering intermediate shaft assembly.
- Align the matchmarks on the steering intermediate shaft assembly and the power steering gear assembly.
- Install the bolt.
Torque: 35 N*m (360 kgf*cm, 26 ft.*lbf)
- Install the clamp to the steering column hole shield with the bolt.
- INSTALL STEERING COLUMN ASSEMBLY
- Install the steering column assembly with the bolt and 2 nuts.
Torque: 21 N*m (210 kgf*cm, 15 ft.*lbf)
- Connect the connectors.
- Install the wire harness clamps to the steering column assembly.
- Install the steering column assembly with the bolt and 2 nuts.
- INSTALL INSTRUMENT PANEL FINISH PLATE
- CONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY
- Align the matchmarks on the intermediate shaft assembly and the steering column assembly.
- Install the bolt.
Torque: 35.0 N*m (360 kgf*cm, 26 ft.*lbf)
- INSTALL AIR DUCT SUB-ASSEMBLY NO.1
- Engage the 2 claws to install the air duct sub-assembly No. 1.
- INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
- Install the turn signal switch assembly w / spiral cable sub-assembly to the steering column assembly with the clamp.
- Install the connectors to the turn signal switch assembly w / spiral cable sub-assembly.
- INSTALL STEERING COLUMN COVER
- Engage the claw to install the steering column cover.
- INSTALL STEERING COLUMN COVER LWR
- Install the steering column cover LWR with the 2 screws.
- PLACE FRONT WHEELS FACING STRAIGHT AHEAD
- CHECK KEY INTERLOCK OPERATION
HINT:
If there is any abnormality, replace the key interlock solenoid.
- CENTER SPIRAL CABLE
- INSTALL STEERING WHEEL ASSEMBLY
- Align the matchmarks on the steering wheel assembly and the steering main shaft assembly.
- Install the steering wheel assembly with the set nut.
Torque: 50 N*m (510 kgf*cm, 37 ft.*lbf)
- Connect the connector.
- INSTALL HORN BUTTON ASSEMBLY (See INSTALLATION )
- INSTALL STEERING WHEEL COVER LOWER NO.2 (See INSTALLATION )
- INSTALL STEERING WHEEL COVER LOWER NO.3 (See INSTALLATION )
- INSTALL INSTRUMENT PANEL AIR BAG ASSEMBLY LOWER NO.1 (See INSTALLATION )
- INSTALL INSTRUMENT PANEL FINISH LOWER PANEL LH
- INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
- INSTALL FRONT DOOR SCUFF PLATE LH
- INSPECT STEERING WHEEL CENTER POINT
HINT:
When the steering wheel is not properly centered, remove and refit to center.
- CONNECT CABLE TO NEGATIVE BATTERY TERMINAL NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
- INSPECT SRS WARNING LIGHT
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
