Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Inspection Procedure
- CHECK THAT MIL IS ILLUMINATEDÂ
- Perform troubleshooting in accordance with the table below:
ResultÂ
RESULT CHARTConditions Proceed to MIL remains ON A MIL does not illuminate B B: Go to step  5
A: Go to next stepÂ
- Perform troubleshooting in accordance with the table below:
- CHECK WHETHER MIL TURNS OFFÂ
- Connect Techstream to the DLC3.
- Turn the ignition switch to ON and turn the tester on.
- Select the following menu items: Powertrain/Engine/Trouble Codes.
- Check if any DTCs have been stored. Note down any DTCs.
- Clear the DTCs (See DTC CHECK/CLEARÂ ).
- Check if the MIL goes off.
Standard:Â
MIL goes off.Â
OK: REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (See  DIAGNOSTIC TROUBLE CODE CHART  )Â
NG: Go to next stepÂ
- CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)Â
- Disconnect the ECM connector.
- Turn the ignition switch to ON.
- Check that the MIL is not illuminated.
OK:Â
MIL is not illuminated.Â
- Reconnect the ECM connector.
OK: REPLACE ECM (See  REMOVAL  )Â
NG: Go to next stepÂ
- CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)Â
- Disconnect the ECM connector.
- Disconnect the combination meter connector.
- Measure the resistance.
Standard resistance (Check for short)Â
RESISTANCE SPECIFIED CONDITIONSTester Connection Specified Condition A55-24 (W) or E3-9 (CHK) - Body ground 10 kΩ or higher - Reconnect the ECM connector.
- Reconnect the combination meter connector.
OK: REPAIR OR REPLACE COMBINATION METER ASSEMBLYÂ
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
NG: REPAIR OR REPLACE HARNESS OR CONNECTORÂ
- CHECK THAT MIL IS ILLUMINATEDÂ
- Check if the MIL is illuminated when the ignition switch is turned to ON.
OK:Â
MIL is illuminated.Â
OK: SYSTEM OKÂ
NG: Go to next stepÂ
- Check if the MIL is illuminated when the ignition switch is turned to ON.
- CHECK THAT ENGINE STARTSÂ
- Turn the ignition switch to ON.
- Start the engine.
ResultÂ
RESULT CHARTResult Proceed to Engine starts A Engine does not start* B HINT:
*: Techstream cannot communicate with the ECM.B: GO TOÂ VC OUTPUT CIRCUITÂ
A: Go to next stepÂ
- INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)Â
- Check the MIL circuit (See PROBLEM SYMPTOMS TABLE
).
NG: REPAIR OR REPLACE COMBINATION METER ASSEMBLYÂ
OK: CHECK AND REPLACE HARNESS AND CONNECTOR (COMBINATION METER - ECM)Â
- Check the MIL circuit (See PROBLEM SYMPTOMS TABLE
).
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
