Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Service Data
MAF meter
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4 (THA) - 2 (E2G) | -20°C (-4°F) | 12.5k to 16.9 kΩ |
| 20°C (68°F) | 2.19 k to 2.67 kΩ | |
| 60°C (140°F) | 0.50 k to 0.68 kΩ |
Camshaft timing oil control valve
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
Engine coolant temperature sensor
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1-2 | Approx. 20°C (68°F) | 2.32 k to 2.59 kΩ |
| Approx. 80°C (176°F) | 0.310 k to 0.326 kΩ |
Throttle W/motor body
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (M-) - 2 (M+) | 20°C (68°F) | 0.3 to 100 Ω |
Accelerator pedal
| Tester display | Accelerator pedal released | Accelerator pedal depressed |
|---|---|---|
| Accelerator position No. 1 | 0.5 to 1.1 V | 2.6 to 4.5 V |
| Accelerator position No. 2 | 1.2 to 2.0 V | 3.4 to 4.7 V |
Knock sensor
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1-2 | 20°C (68°F) | 120 to 280 kΩ |
Ignition relay No. 2
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IG2 MAIN fuse | Always | Below 1 Ω |
| 1C-1-1B-8 | When battery voltage is not applied to terminals 1B-6 and 1B-7 | 10 kΩ or higher |
| When battery voltage is applied to terminals | 1B-6 and 1B-7 Below 1 Ω |
EFI relay
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI No. 1 fuse | Always | Below 1 Ω |
| 1C-1 -1B-4 1C-1 -1B-5 |
When battery voltage is not applied to terminals 1B-2 and 1B-3) | 10 kΩ or higher |
| When battery voltage is applied to terminals 1B-2 and 1B-3) | Below 1 Ω |
Circuit opening relay
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3-5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
Fuel pump relay
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3-5 | When battery voltage is not applied to terminals 1 and 2 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1 and 2 | Below 1 Ω |
Air fuel ration sensor (for Bank 1 sensor 1)
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (HA1A)-2(+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
Air fuel ration sensor (for Bank 2 sensor 1)
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (HA2A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
Heated oxygen sensor (for Bank 1 sensor 2)
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (HT1B)-2(+B) | 20°C (68°F) | 11 to 16 Ω |
Heated oxygen sensor (for Bank 2 sensor 2)
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 (HT2B) - 2 (+B) | 20°C (68°F) | 11 to 16 Ω |
A/F sensor heater relay
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A/F fuse | Always | Below 1 Ω |
| 1C-1 -1A-4 | When battery voltage is not applied to terminals 1A-2 and 1A-3 | 10 kΩ or higher |
| When battery voltage is applied to terminals 1A-2 and 1A-3 | Below 1 Ω |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
