Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
How To Proceed With Troubleshooting
Techstream can be used in steps  2,  3,  4,  6 and  9.
- VEHICLE BROUGHT TO WORKSHOPÂ
- CONNECT TECHSTREAM TO DLC3Â
HINT:
If the display indicates a communication fault in Techstream, inspect the DLC3.
- CHECK DTC AND FREEZE FRAME DATAÂ
- Check the DTC(s) and freeze frame data (See DTC CHECK / CLEARÂ
).
HINT:
Record or print DTCs and freeze frame data, if necessary.
- Check the DTC(s) and freeze frame data (See DTC CHECK / CLEARÂ
).
- CLEAR DTC AND FREEZE FRAME DATAÂ
- Clear the DTC(s) and freeze frame data (See DTC CHECK / CLEARÂ ).
- CONDUCT VISUAL INSPECTIONÂ
- SET CHECK MODE DIAGNOSISÂ
- Set the check mode (See CHECK MODE PROCEDUREÂ ).
- CONFIRM PROBLEM SYMPTOMSÂ
HINT:
If the engine does not start, perform steps  9 and  11 first.
ResultÂ
DTC RESULT DESCRIPTION CHARTResult Proceed to Malfunction does not occur A Malfunction occurs B B:Â GO TO STEP Â 9
A: Go to Next StepÂ
- SIMULATE SYMPTOMSÂ
- CHECK DTCÂ
- Check the DTC(s) (See DTC CHECK / CLEARÂ
).
ResultÂ
DTC RESULT DESCRIPTION CHARTResult Proceed to Malfunction code A No code B
B:Â GO TO STEP Â 11
A: Go to Next StepÂ
- Check the DTC(s) (See DTC CHECK / CLEARÂ
).
- REFER TO DTC CHARTÂ
HINT:
Refer to "DTC CHARTÂ " .
NEXT:Â GO TO STEP Â 13
- CONDUCT BASIC INSPECTIONÂ
HINT:
Refer to "BASIC INSPECTIONÂ " .
ResultÂ
DTC RESULT DESCRIPTION CHARTResult Proceed to Malfunctioning parts not confirmed A Malfunctioning parts confirmed B B:Â GO TO STEP Â 16
A: Go to Next StepÂ
- REFER TO PROBLEM SYMPTOMS TABLEÂ
HINT:
Refer to "PROBLEM SYMPTOMS TABLEÂ " .
ResultÂ
DTC RESULT DESCRIPTION CHARTResult Proceed to Malfunctioning circuit confirmed A Malfunctioning parts confirmed B B:Â Go TO STEP Â 16
A: Go to Next StepÂ
- CHECK ECM POWER SOURCE CIRCUITÂ
HINT:
Refer to "ECM POWER SOURCE CIRCUITÂ " .
- CONDUCT CIRCUIT INSPECTIONÂ
ResultÂ
DTC RESULT DESCRIPTION CHARTResult Proceed to Malfunction not confirmed A Malfunction confirmed B B:Â GO TO STEP Â 17
A: Go to Next StepÂ
- CHECK FOR INTERMITTENT PROBLEMSÂ
HINT:
(See CHECK FOR INTERMITTENT PROBLEMSÂ ).
NEXT:Â GO TO STEP Â 17
- CONDUCT PARTS INSPECTIONÂ
- IDENTIFY PROBLEMÂ
- ADJUST AND/OR REPAIRÂ
- CONDUCT CONFIRMATION TESTÂ
NEXT : ENDÂ
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
