2008 Toyota Matrix Base, AutomaticFACTORY OEM SERVICE PROCEDURE

Fuel System: Precaution

  1. PRECAUTION 
    1. Before working on the fuel system, disconnect the battery negative terminal.
    2. Do not work on the fuel system near fire. Never smoke during the work.
    3. Keep rubber and leather parts away from gasoline.
  2. DISCHARGE FUEL SYSTEM PRESSURE 
    CAUTION:
    • Before removing fuel system parts, take precautions to prevent gasoline spillage.
    • As some pressure remains in the fuel line even after taking precautions to prevent gasoline spillage, use a shop rag to prevent gasoline splashes when disconnecting the fuel line.
    1. Disconnect the battery negative terminal.
    2. Remove the rear seat cushion (See REMOVAL ).
    3. Remove the rear floor service hole cover (See REMOVAL  ).
    4. Disconnect the fuel pump connector.
    5. Connect the engine wire (battery negative terminal).

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

    6. Start the engine.
    7. After the engine stops, turn the ignition switch off.

      HINT:

      DTC P0171 (system to lean) may be present.

      Fig 1: Identifying Fuel Pump Connector
      G05193192Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. Crank the engine again, and check that the engine does not start.
    9. Remove the fuel tank cap and discharge the pressure in the fuel tank completely.
    10. Disconnect the battery negative terminal.
    11. Connect the fuel pump connector.
    12. Install the rear floor service hole cover (See INSTALLATION  ).
    13. Install the rear seat cushion (See INSTALLATION ).
    14. Connect the battery negative terminal.

      Torque: 5.4 N*m (55 kgf*cm, 48 in.*lbf) 

  3. FUEL SYSTEM 
    1. When disconnecting the high-pressure fuel line, a large amount of gasoline will splash. So take the following precautions:
      1. Discharge the fuel system pressure.
      2. Disconnect the fuel tube (See ON-VEHICLE INSPECTION  ).
      3. Release the pressure remaining in the fuel tank main tube.
      4. Cover the disconnected fuel tank main tube (fuel tube joint and fuel tube connector) with a vinyl bag to prevent damage and the intrusion of foreign objects.
      5. Put a container under the connection.
        Fig 2: Covering Disconnected Fuel Tank Main Tube And Fuel Tube Connector With Vinyl Bag
        G05193193Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Take the following precautions when removing and installing the fuel injector.
      1. Do not reuse the O-ring.
      2. Do not damage a new O-ring when installing it onto the fuel injector.
      3. Before installing a new O-ring, apply gasoline or spindle oil onto the fuel injector.
        NOTE: Do not use engine oil, gear oil or brake oil.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.