2008 Toyota Matrix Base, AutomaticFACTORY OEM SERVICE PROCEDURE

Diagnostic Trouble Code Chart

NOTE: When removing parts, turn the ignition switch off.

HINT:

  • Using SST 09843-18040, connect terminals TC and CG of the DLC3.
  • If no abnormality is found when inspecting parts, inspect the ECU and ground points for poor contact.
  • If a trouble code is displayed during the DTC check, check the circuit listed for that code.
  • When 2 or more DTCs are recorded and the problem is not identified, perform circuit inspection of the other DTCs.

DTC chart of ABS: 

DTC CHART OF ABS

DTC Code Detection Item Trouble Area
C0200/31  Front Speed Sensor RH Circuit
  1. Right front speed sensor
  2. Right front speed sensor circuit
  3. Right front speed sensor rotor
  4. Sensor installation
C0205/32  Front Speed Sensor LH Circuit
  1. Left front speed sensor
  2. Left front speed sensor circuit
  3. Left front speed sensor rotor
  4. Sensor installation
C0210/33  Rear Speed Sensor RH Circuit
  1. Right rear speed sensor
  2. Right rear speed sensor circuit
  3. Right rear speed sensor rotor
  4. Sensor installation
C0215/34  Rear Speed Sensor LH Circuit
  1. Left rear speed sensor
  2. Left rear speed sensor circuit
  3. Left rear speed sensor rotor
  4. Sensor installation
C0226/21  SFR Solenoid Circuit
  1. Brake actuator assembly
  2. SFRR or SFRH circuit
C0236/22  SFL Solenoid Circuit
  1. Brake actuator assembly
  2. SFLR or SFLH circuit
C0246/23  SRR Solenoid Circuit
  1. Brake actuator assembly
  2. SRRR or SRRH circuit
C0256/24  SRL Solenoid Circuit
  1. Brake actuator assembly
  2. SRLR or SRLH circuit
C0273/13  Open in ABS Motor Relay Circuit
  1. ABS motor relay
  2. ABS motor relay circuit
  3. Brake actuator assembly
C0274/14  Short to B+ in ABS Motor Relay Circuit
  1. ABS motor relay
  2. ABS motor relay circuit
  3. Brake actuator assembly
C0278/11  Open in ABS Solenoid Relay Circuit
  1. ABS solenoid relay
  2. ABS solenoid relay circuit
  3. Brake actuator assembly
C0279/12  Short to B+ in ABS Solenoid Relay Circuit
  1. ABS solenoid relay
  2. ABS solenoid relay circuit
  3. Brake actuator assembly
C1235/35  Foreign Object is Attached on Tip of Front Speed Sensor RH
  1. Right front speed sensor
  2. Right front speed sensor rotor
C1236/36  Foreign Object is Attached on Tip of Front Speed Sensor LH
  1. Left front speed sensor
  2. Left front speed sensor rotor
C1238/38  Foreign Object is Attached on Tip of Rear Speed Sensor RH
  1. Right rear speed sensor
  2. Right rear speed sensor rotor
C1239/39  Foreign Object is Attached on Tip of Rear Speed Sensor LH
  1. Left rear speed sensor
  2. Left rear speed sensor rotor
C1241/41  Low Battery Positive Voltage
  1. Battery
  2. Charging system
  3. Power source circuit
C1249/49  Open in Stop Light Switch Circuit
  1. Stop light switch
  2. Stop light switch circuit
C1251/51  Open in Pump Motor Circuit
  1. ABS pump motor
  2. Brake actuator assembly

Test mode DTC of ABS: 

TEST MODE DTC OF ABS

DTC Code Detection Item Trouble Area
C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
  1. Front speed sensor RH
  2. Sensor installation
  3. Sensor rotor
C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
  1. Front speed sensor LH
  2. Sensor installation
  3. Sensor rotor
C1273/73  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)
  1. Rear speed sensor RH
  2. Sensor installation
  3. Sensor rotor
C1274/74  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)
  1. Rear speed sensor LH
  2. Sensor installation
  3. Sensor rotor
C1275/75  Abnormal Change in Output Signal of Front Speed Sensor RH (Test Mode DTC) Front speed sensor rotor RH
C1276/76  Abnormal Change in Output Signal of Front Speed Sensor LH (Test Mode DTC) Front speed sensor rotor LH
C1277/77  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Rear speed sensor rotor RH
C1278/78  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Rear speed sensor rotor LH
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.