Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Toyota Matrix Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Audio System & Visual System
- Audio And Visual System
- Precaution
- Parts Location
- System Diagram
- System Description
- How To Proceed With Troubleshooting
- Identification Of Noise Source
- Problem Symptoms Table
- Terminals Of Ecu
- DTC Check / Clear
- Diagnostic Trouble Code Chart
- DTC 01-21 ROM Error; DTC 01-22 RAM Error
- DTC 01-D5 Absence of Registration Unit; DTC 01-D8 No Response for Connection Check; DTC 01-D9 Last Mode Error; DTC 01-DA No Response Against ON / OFF Command; DTC 01-DB Mode Status Error; DTC 01-DE Slave Reset
- DTC 01-D6 No Master; DTC 01-D7 Connection Check Error
- DTC 01-DC Transmission Error
- DTC 01-DD Master Reset; DTC 01-E1 Voice Processing Device ON Error
- DTC 01-DF Master Error
- DTC 01-E0 Registration Complete Indication Error; DTC 01-E3 Registration Demand Transmission; DTC 01-E4 Multiple Frame Incomplete
- DTC 01-E2 ON / OFF Indication Parameter Error
- DTC 62-10 CD Player Mechanical Error; DTC 62-11 CD Insertion and Ejection Error; DTC 62-12 CD Reading Abnormal; DTC 63-10 CD Changer Mechanical Error; DTC 63-11 CD Insertion and Ejection Error; DTC 63-12 CD Reading Abnormal
- DTC 62-41 Wrong Disc; DTC 62-42 Disc cannot be Read; DTC 63-41 Wrong Disc; DTC 63-42 Disc cannot be Read
- DTC 62-43 CD-ROM Abnormal; DTC 63-43 CD-ROM Abnormal
- DTC 62-44 CD Abnormal; DTC 62-48 Excess Current; DTC 62-50 Tray Insertion / Ejection Error; DTC 63-44 CD Abnormal; DTC 63-48 Excess Current; DTC 63-50 Tray Insertion / Ejection Error
- DTC 62-45 Eject Error; DTC 62-51 Elevator Error; DTC 62-52 Clamp Error; DTC 63-45 Eject Error; DTC 63-51 Elevator Error; DTC 63-52 Clamp Error
- DTC 62-46 Scratched / Reversed Disc; DTC 63-46 Scratched / Reversed Disc
- DTC 62-47 High Temperature; DTC 63-47 High Temperature
- Noise Occurs
- Sound Quality is Bad in All Modes
- Sound Quality is Bad Only when CD is Played (Volume is Too Low)
- CD cannot be Ejected
- CD cannot be Inserted / Played or CD is Ejected Right After Insertion
- CD Sound Skips
- Radio Broadcast cannot be Received or Poor Reception
- Illumination Circuit
- Speaker Circuit
- Sound Signal Circuit between Radio Receiver and Stereo Component Amplifier
- Mute Signal Circuit between Radio Receiver and Stereo Component Amplifier
- AVC-LAN Circuit
- Radio Receiver Communication Error
- Stereo Component Amplifier Communication Error
- Radio Receiver Power Source Circuit
- Stereo Component Amplifier Power Source Circuit
- Radio Receiver
- Stereo Component Amplifier
- Front Side Speaker
- Rear Side Speaker
- Radio Antenna Cord
- Radio Antenna Pole
- Amplifier Antenna
- Luggage Speaker
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
Rather have a pro handle this?
A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.
Comes to youSame-day available12-month warranty
Get a Free QuoteNo obligation. See pricing before you book.