Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Toyota Highlander HybridFACTORY OEM SERVICE PROCEDURE
Knock Sensor: Removal
- DISCHARGE FUEL SYSTEM PRESSUREÂ
HINT:
See PRECAUTION .
- DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINALÂ CAUTION: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
- REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LHÂ (See REMOVAL )
- REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RHÂ (See REMOVAL )
- REMOVE HOOD TO COWL TOP SEALÂ (See REMOVAL )
- REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLYÂ (See REMOVAL )
- REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLYÂ (See REMOVAL )
- REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLYÂ (See REMOVAL )
- REMOVE COOL AIR INTAKE DUCT SEALÂ (See REMOVAL )
- REMOVE NO. 2 ENGINE ROOM SIDE COVER LHÂ (See REMOVAL )
- DRAIN ENGINE COOLANT (for Engine)Â (See REPLACEMENT )
- REMOVE AIR CLEANER CAP SUB-ASSEMBLYÂ (See REMOVAL )
- REMOVE AIR CLEANER CASE SUB-ASSEMBLYÂ (See REMOVAL )
- SEPARATE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLYÂ (See REMOVAL )
- REMOVE AIR CLEANER BRACKETÂ (See REMOVAL )
- REMOVE ENGINE MOVING CONTROL RODÂ (See REMOVAL )
- REMOVE EMISSION CONTROL VALVE SETÂ (See REMOVAL )
- REMOVE INTAKE AIR SURGE TANKÂ (See REMOVAL )
- DISCONNECT FUEL PIPE SUB-ASSEMBLYÂ
- Remove the No. 1 EFI fuel pipe clamp.
- Pinch the quick connector and then pull out the No. 1 fuel pipe.NOTE:
- Remove dirt or foreign objects on the quick connector before disconnecting the connector.
- Do not allow any scratches or foreign objects on the connecting surfaces when disconnecting as the fuel hose connector has the O-ring that seals the pipe.
- Perform this work by hand. Do not use any tools.
- Do not forcibly bend, twist or turn the nylon tube.
- Protect the connecting surfaces by covering them with a vinyl bag after disconnecting the pipe.
- If the quick connector and pipe are stuck, push and pull to release them.
- DISCONNECT INLET HEATER WATER HOSEÂ
- Disconnect the inlet heater water hose.
- DISCONNECT INLET RADIATOR HOSEÂ
- Disconnect the inlet radiator hose.
- REMOVE INTAKE MANIFOLDÂ
- Remove the nut and disconnect the ground cable.
- Disconnect the 6 fuel injector connectors.
- In order to remove the intake manifold, using several steps, remove the 9 bolts, 2 washers and 2 nuts in the sequence shown in the illustration.
- REMOVE OUTLET WATERÂ (See REMOVAL )
- REMOVE KNOCK CONTROL SENSORÂ
- Disconnect the 2 knock sensor connectors.
- Remove the 2 nuts, and then remove the 2 knock sensors.
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
