Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2008 Toyota Highlander HybridFACTORY OEM SERVICE PROCEDURE
Knock Sensor: Installation
- INSTALL KNOCK CONTROL SENSORÂ
- Install the 2 knock sensors so that it is horizontal as shown in the illustration. Then install the 2 bolts.
Torque: 20 N*m (199 kgf*cm, 15 ft.*lbf)Â
HINT:
It is acceptable for the sensor to be tilted 5°.
- Connect the 2 knock sensor connectors.
- Install the 2 knock sensors so that it is horizontal as shown in the illustration. Then install the 2 bolts.
- INSTALL OUTLET WATERÂ (See INSTALLATION )
- INSTALL INTAKE MANIFOLDÂ
- Install the intake manifold with the 9 bolts, 2 nuts and 2 washers. Using several steps, tighten the bolts and nuts uniformly in the sequence shown in the illustration.
Torque: 15 N*m (153 kgf*cm, 11 ft.*lbf)Â
- Retighten the outlet water mounting bolts and nuts.
Torque: 15 N*m (153 kgf*cm, 11 ft.*lbf)Â
- Connect the 6 fuel injector connectors.
- Install the ground cable with the nut.
Torque: 8.4 N*m (86 kgf*cm, 74 in.*lbf)Â
- Install the intake manifold with the 9 bolts, 2 nuts and 2 washers. Using several steps, tighten the bolts and nuts uniformly in the sequence shown in the illustration.
- CONNECT INLET RADIATOR HOSEÂ
- Connect the inlet radiator hose.
- CONNECT INLET HEATER WATER HOSEÂ
- Connect the inlet heater water hose.
- CONNECT FUEL PIPE SUB-ASSEMBLYÂ
- Align the quick connector with the pipe, then push in the quick connector until the retainer makes a "click" sound to connect the fuel hose to the fuel pipe.NOTE:
- Check that there are no scratches or foreign objects around the connecting surfaces of the quick connector and pipe before this work.
- After connecting the fuel pipe, confirm that it is securely connected by pulling the quick connector.
- Install the No. 1 fuel pipe clamp.
- Align the quick connector with the pipe, then push in the quick connector until the retainer makes a "click" sound to connect the fuel hose to the fuel pipe.
- INSTALL INTAKE AIR SURGE TANKÂ (See INSTALLATION )
- INSTALL EMISSION CONTROL VALVE SETÂ (See INSTALLATION )
- INSTALL ENGINE MOVING CONTROL RODÂ (See INSTALLATION )
- INSTALL AIR CLEANER BRACKETÂ (See INSTALLATION )
- INSTALL BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLYÂ (See INSTALLATION )
- INSTALL AIR CLEANER CASE SUB-ASSEMBLYÂ (See INSTALLATION )
- INSTALL AIR CLEANER CAP SUB-ASSEMBLYÂ (See INSTALLATION )
- ADD ENGINE COOLANT (for Engine)Â (See REPLACEMENT )
- CONNECT CABLE TO NEGATIVE BATTERY TERMINALÂ NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See INITIALIZATION ).
- INSPECT FOR COOLANT LEAK (for Engine)Â (See ON-VEHICLE INSPECTION )
- INSPECT FOR FUEL LEAKÂ (See ON-VEHICLE INSPECTION )
- INSTALL NO. 2 ENGINE ROOM SIDE COVER LHÂ (See INSTALLATION )
- INSTALL COOL AIR INTAKE DUCT SEALÂ (See INSTALLATION )
- INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLYÂ (See INSTALLATION )
- INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLYÂ (See INSTALLATION )
- INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLYÂ (See INSTALLATION )
- INSTALL HOOD TO COWL TOP SEALÂ (See INSTALLATION )
- INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RHÂ (See INSTALLATION )
- INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LHÂ (See INSTALLATION )
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
