Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
2007 Toyota Matrix Base, AutomaticFACTORY OEM SERVICE PROCEDURE
Technical Service Bulletins
- A/C Compressor
- Accessories & Equipment
- Accessories Control Systems
- Accessory Drive Belts
- Air Bag, SRS
- Anti-Lock Brakes
- Anti-Theft Systems
- Automatic Trans
- Automatic/Continuously Variable Transmission Replacement Precautions (T-SB-0024-18)
- Remanufactured Automatic Transmission Serial Number Location (TC013-06)
- Automatic Transmission Serial Number Location (TC012-06)
- 1ZZ-FE Engine Control Module (ECM) Parts Information (T-SB-0378-08)
- Special Service Tools (T-SB-0302-08)
- Alignment Pin Installation During Transmission/Transaxle Assembly Installation (T-SB-0053-08)
- Harsh Shift And M.I.L. "On" DTC P2716 (TC015-07)
- Automatic Transmission Shipping Bag For Warranty Recovery (TC012-07)
- Auxiliary Emission Control Systems
- Axle Shafts
- Battery Management Systems
- Body Electrical
- Brakes Control Systems
- Charging Systems
- Cooling System (Mechanical)
- Cruise Control Systems
- Driveshaft & Universal Joints
- Engine Control Systems
- Entertainment Systems
- Exterior Body Panels
- Frames, Subframes & Crossmembers
- Front Suspension
- Fuel System
- Fuses & Circuit Breakers
- Hazardous Waste Material
- HVAC Control Systems
- Identification
- Replacement Certification Labels And VIN Plates (T-SB-0032-20 REV2)
- Replacement VIN Plates (PG009-02)
- Replacement VIN Plates (PG005-97)
- Remanufactured Automatic Transmission Serial Number Location (TC013-06)
- Automatic Transmission Serial Number Location (TC012-06)
- Ca/Fed/50 State Certified Emission Control UNDERHOOD Labels (T-SB-0054-13)
- Engine Serial Number Location (T-SB-0301-08 REV1)
- Replacement Certification Labels And VIN Plates - Crib # 164 (S-CRIB-164)
- Infotainment
- Interior/Exterior Trim
- Lubrication System
- Mechanical
- Mechanical - Hydraulic
- Wheel Film For Brake Rotor Rust Prevention (T-SB-0038-24 REV2)
- Flood Damaged Vehicle Inspection & Handling (T-SB-0229-12 REV1)
- TCMC Front Brake Pad Noise (T-SB-0150-13)
- Brake Pedal Force Gauge SST For Parking Brake (T-SB-0141-13)
- Special Service Tools (T-SB-0302-08)
- Front Brake Rattle Noise (T-SB-0046-08)
- Memory Modules
- Paint & Coatings
- New Vehicle Washing Schedule For Paint Protection (T-SB-0039-24 REV2)
- Prevention And Repair Of Acid Rain Damage (T-SB-091-020)
- RAPGARD Protective Film Removal (T-SB-0061-23 REV2)
- Iron Particle Rust Contamination Repair (TS-PA005-04)
- PAINTLESS Dent Repair - Crib # 146 (T-CRIB-146)
- Long Term Vehicle Storage Guidelines (T-SB-0079-09 REV1)
- Plastic Bumper Refinishing - Crib # 170 (L-CRIB-170)
- Permanent-Type Protective Wax Coatings (T-SB-0138-08)
- Acid Rain Paint Finish Damage - Prevention & Repair - Crib # 165 (S-CRIB-165)
- Exterior Color And Scratch Resistant And Anti-Acid Paint (PA003-07)
- Paint Stains Under RAPGARD™ (PA002-06)
- Refinishing Replacement Bumper Covers (PA001-07)
- Passive Restraints
- Procedures
- Rear Suspension
- Restraints Control Systems
- Seats
- Starter
- Steering Linkage
- Suspension Control Systems
- System
- M.I.L. "On" DTC P0171, P0441, And/Or P0455 (EG041-07)
- Mil "On" DTC P0456 (T-SB-0235-09 REV1)
- 1ZZ-FE Engine Control Module (ECM) Parts Information (T-SB-0378-08)
- M.I.L. "On" DTC P0171, P030#, And/Or P0133 Engine Running Lean In Subfreezing Ambient Temperatures (EG045-07)
- Harsh Shift And M.I.L. "On" DTC P2716 (TC015-07)
- M.I.L. "On" DTC P0136, P0138, And/Or P2195 (EG043-07)
- M.I.L. "On" DTC P0601, P0606, And/Or P0607 Or Engine "No Start" Condition (EG049-06R)
- M.I.L. "On" DTC P0011, P0012, Or P0016 (EG005-07)
- Transmission Control Systems
- Warning Systems
- Wheel Alignment
- Wheels & Tire System
- Window Motors & Regulators
- Wiper/Washer Systems
- Wiring System (Data Link Connectors, Pwr Dist., Grnd Dist.)
Factory Service Tools
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.