2007 Toyota FJ Cruiser 4WD, AutomaticFACTORY OEM SERVICE PROCEDURE

Repair Instruction: Precaution

  1. BASIC REPAIR HINT 
    1. HINTS ON OPERATIONS
      Fig 1: Identifying Precaution For Repair Instruction
      G05108041Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. JACKING UP AND SUPPORTING VEHICLE
      1. Care must be taken when jacking up and supporting the vehicle. Be sure to lift and support the vehicle at the proper locations.
    3. PRECOATED PARTS
      1. Precoated parts are bolts and nuts that are coated with a seal lock adhesive at the factory.
      2. If a precoated part is retightened, loosened or moved in any way, it must be recoated with the specified adhesive.
      3. When reusing a precoated part, clean off the old adhesive and dry the part with compressed air. Then apply new seal lock adhesive appropriate to that part.
      4. Some seal lock agents harden slowly. You may have to wait for the seal lock adhesive to harden.
        Fig 2: Identifying Seal Lock Adhesive
        G04827550Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    4. GASKET
      1. When necessary, use a sealer on gaskets to prevent leaks.
    5. BOLTS, NUTS AND SCREWS
      1. Carefully follow all the specifications for tightening torques. Always use a torque wrench.
    6. FUSES
      1. When inspecting a fuse, check that the wire of the fuse is not broken.
      2. When replacing fuses, be sure that the new fuse has the correct amperage rating. Do not exceed the rating or use one with a lower rating.
        Fig 3: Identifying Precaution For Fuse
        G04827551Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        FUSE SYMBOL REFERENCE

        Graphic Symbol Part Name Abbreviation
        G05108044Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        G05108045Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        		 FUSE FUSE
        G05108046Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        G05108047Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        		 MEDIUM CURRENT FUSE M-FUSE
        G05108048Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        G05108049Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        		 HIGH CURRENT FUSE H-FUSE
        G05108050Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        G05108051Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        		 FUSIBLE LINK FL
        G05108052Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        G05108053Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
        		 CIRCUIT BREAKER CB
    7. clips
      1. The removal and installation methods of typical clips used for vehicle body parts are shown in Fig 4.

        HINT:

        If clips are damaged during a procedure, always replace the damaged clip with a new clip.

        Fig 4: Identifying Removal & Installation Methods Of Typical Clips
        G05108054Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    8. CLAWS
      1. The removal and installation methods of typical claws used for vehicle body parts are shown in Fig 5.

        HINT:

        If claws are damaged during a procedure, always replace the damaged claws with new caps or covers.

        Fig 5: Identifying Claws Removal & Installation Procedure Chart
        G05108055Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    9. REMOVAL AND INSTALLATION OF VACUUM HOSES
      1. To disconnect a vacuum hose, pull and twist from the end of the hose. Do not pull from the middle of the hose as this may cause damage.
        Fig 6: Identifying Precaution For Vacuum Hose
        G04827580Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      2. When disconnecting vacuum hoses, use tags to identify where they should be reconnected.
      3. After completing any hose related repairs, double check that the vacuum hoses are properly connected. The label under the hood shows the proper layout.
      4. When using a vacuum gauge, never force the hose onto a connector that is too large. If a hose has been stretched, it may leak air. Use a step-down adapter if necessary.
        Fig 7: Identifying Tag On Vacuum Hoses
        G04827581Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    10. TORQUE WHEN USING TORQUE WRENCH WITH EXTENSION TOOL
      Fig 8: Identifying Torque Wrench Dimension
      G04827582Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
      1. Use the formula below to calculate special torque values for situations where SST or an extension tool is combined with a torque wrench.

        Formula: 

        T' = L2 / (L1 + L2) * T 

        FORMULA TABLE

        T' Reading of torque wrench {N*m (kgf*cm, ft.*lbf)}
        T Torque {N*m (kgf*cm, ft.*lbf)}
        L1 Length of SST or extension tool {cm (in.)}
        L2 Length of torque wrench {cm (in.)}
        NOTE: If an extension tool or SST is combined with a torque wrench and the wrench is used to tighten to a torque specification in this article, the actual torque will be excessive and parts will be damaged.
Factory Service Tools

Use the Manual With the Right Hardware

Pair factory procedures with proven DIY tools so the instructions are easier to execute.

Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.

Shop Manual-Ready ToolsCompare Repair QuoteQuote Shield Pro

When to See a Mechanic

Stop DIY work and contact a certified mechanic immediately if any of the following apply:

  • • You smell fuel, burning insulation, or see smoke.
  • • Brakes feel soft, pull hard to one side, or make grinding noises.
  • • The engine overheats, stalls repeatedly, or misfires under load.
  • • You are missing required tools, torque specs, or safe lifting equipment.
  • • You are not confident in the next step or safety outcome.

Rather have a pro handle this?

A certified mobile mechanic comes to your home or office. They bring the tools, you stay comfortable. No tow truck, no waiting room, no surprises.

Comes to youSame-day available12-month warranty
Get a Free Quote

No obligation. See pricing before you book.