Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
Typical Malfunction Thresholds
| One of the following conditions is met: | - |
| EVAP pressure just after reference pressure measurement start | -1 kPa (7.5 mmHg) or higher |
| Reference pressure (0.02 inch leak pressure) | -1.2 kPa (-9 mmHg) or higher |
| Reference pressure (0.02 inch leak pressure) | Lower than -4.3 kPa (-32 mmHg) |
| Reference pressure (0.02 inch leak pressure) | Not saturated for 60 seconds |
- Purge VSV stuck openPURGE VSV STUCK OPEN MALFUNCTION THRESHOLDS
EVAP pressure when vacuum introduction is complete Higher than reference pressure x 0.2 - Purge VSV stuck closedPURGE VSV STUCK CLOSED MALFUNCTION THRESHOLDS
EVAP pressure change after EVAP canister purge valve is open Less than 0.3 kPa (2.25 mmHg)
| Both of the following conditions set: | - |
| EVAP pressure change when purge flow is started | 0.1 kPa (0.75 mmHg) or less |
| EVAP pressure change during purge flow when EVAP pressure switching valve is ON (closed) | 1 kPa (7.5 mmHg) or less |
P0450 (Pressure sensor fluctuating):
| Pressure sensor pressure | Less than 42.11 kPa, or more than 123.761 kPa |
P0451 (Pressure sensor noise):
| Frequency that EVAP pressure change is 0.3 kPa or more | 10 times or more in 10 seconds |
P0451 (Pressure sensor stuck):
| EVAP pressure change during reference pressure measurement | Less than 0.8 kPa (6 mmHg) |
P0452 (Pressure sensor low):
| Pressure sensor pressure | Less than 42.11 kPa |
P0453 (Pressure sensor high):
| Pressure sensor pressure | More than 123.761 kPa |
"Saturated" indicates that the EVAP (Evaporative Emission) pressure change is less than 0.1 kPa (0.75 mmHg) in 30 seconds.
P0455 (EVAP gross leak):
| EVAP pressure when vacuum introduction is complete | Higher than reference pressure x 0.2 |
P0456 (EVAP small leak):
| EVAP pressure when vacuum introduction is complete | Between reference pressure and reference pressure x 0.2 |
| One of the following conditions is met: | - |
| EVAP pressure when reference pressure measurement started | -1 kPa (7.5 mmHg) or higher |
| Reference pressure (0.02 inch leak pressure) | -1.2 kPa (-9 mmHg) or higher |
| Reference pressure (0.02 inch leak pressure) | Lower than -4.3 kPa (-32 mmHg) |
| Reference pressure (0.02 inch leak pressure) | Not saturated for 60 seconds |
P2419 (Vent valve stuck ON (Open)):
| One of the following conditions is met: | - |
| EVAP pressure when reference pressure measurement started | -1 kPa (7.5 mmHg) or higher |
| Reference pressure (0.02 inch leak pressure) | -1.2 kPa (-9 mmHg) or higher |
| Reference pressure (0.02 inch leak pressure) | Lower than -4.3 kPa (-32 mmHg) |
| Reference pressure (0.02 inch leak pressure) | Not saturated for 60 seconds |
P2420 (Vent valve stuck OFF (Close))
| EVAP pressure change after EVAP canister vent valve is ON | Less than 0.3 kPa (2.25 mmHg) |
Case 1:
| Soak timer measurement when ECM CPU clock counts 10 minutes | Less than 7 minutes or more than 13 minutes |
Case 2:
| History ECM had woken up by internal engine off timer | Yes |
| How long vehicle has been soaked | Less than programmed period |
Case 3:
| History ECM had woken up by internal engine off timer | No |
| How long vehicle has been soaked | More than or equal to programmed period |
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Disclosure: Verified tool recommendations may earn an affiliate commission at no cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.
