Safety Warning
DIY auto repair can cause serious injury, fire, or vehicle damage. These guides are for informational purposes only. Always follow OEM torque specs, wear PPE, and consult a certified mechanic if you are unsure. You are solely responsible for your safety.
SYS.OK|MANUAL.DB● LIVE
HOMESERVICE MANUALSTOYOTA2006MATRIX BASE, FWD, STANDARDREPAIR AND DIAGNOSISENGINE PERFORMANCEENGINE CONTROL SYSTEMSPREPARATIONA246E AUTOMATIC TRANSAXLESST
2006 Toyota Matrix Base, FWD, Standard
A246E Automatic Transaxle: SST
2006 Toyota Matrix Base, FWD, StandardSECTION SST
A246E AUTOMATIC TRANSAXLE SPECIAL SERVICE TOOL
| 09023-12701 | Union Nut Wrench 17mm | |
| 09240-00020 | Wire Gauge Set | |
| 09249-63010 | Torque Wrench Adaptor | |
| 09308-00010 | Oil Seal Puller | |
| 09330-00021 | Companion Flange Holding Tool | |
| (09351-32032) | Counter Driven Gear Holding Tool | |
| 09350-32014 | TOYOTA Automatic Transmission Tool Set | |
| (09351-32010) | One-way Clutch Test Tool | |
| (09351-32020) | Stator Stopper | |
| (09351-32032) | Counter Driven Gear Holding Tool | |
| (09351-32040) | No.1 Piston Spring Compressor | |
| (09351-32050) | Snap Ring Expander | |
| (09351-32061) | Oil Pump Puller | |
| (09351-32070) | No.2 Piston Spring Compressor | |
| (09351-32090) | Oil Seal Remover & Replacer | |
| (09351-32100) | Drive Pinion Bearing Replacer | |
| (09351-32111) | Side Bearing Race Replacer | |
| (09351-32120) | Overdrive Bearing Replacer | |
| (09351-32130) | Handle | |
| (09351-32140) | Oil Seal Replacer | |
| (09351-32150) | Oil Seal Replacer | |
| (09351-32170) | Lock Nut Wrench | |
| (09351-32180) | Bearing Replacer | |
| (09351-32190) | Measure Terminal | |
| 09520-01010 | Drive Shaft Remover Attachment | |
| 09520-24010 | Differential Side Gear Shaft Puller | |
| (09520-32040) | Shocker Set | |
| 09564-32011 | Differential Preload Adaptor | |
| 09710-30031 | Rear Suspension Bushing Tool Set | |
| (09710-03161) | Remover | |
| 09950-00020 | Bearing Remover | |
| 09950-40011 | Puller B Set | |
| (09951-04010) | Hanger 150 | |
| (09952-04010) | Slide Arm | |
| (09953-04030) | Center Bolt 200 | |
| (09954-04010) | Arm 25 | |
| (09955-04061) | Claw No.6 | |
| (09957-04010) | Attachment | |
| (09958-04011) | Holder | |
| 09950-60010 | Replacer Set | |
| (09951-00340) | Replacer 34 | |
| (09951-00380) | Replacer 38 | |
| (09951-00410) | Replacer 41 | |
| 09950-70010 | Handle Set | |
| (09951-07100) | Handle 100 | |
| 09960-10010 | Variable Pin Wrench Set | |
| (09962-01000) | Variable Pin Wrench Arm Assembly | |
| (09963-01000) | Pin 10 |
RENDER: 1.0x
NO RELATED
Recommended Tools & Savings
Use the Manual With the Right Hardware
Pair factory procedures with proven DIY tools so the instructions are easier to execute.
Affiliate disclosure: We may earn a commission at no extra cost to you.
When to See a Mechanic
Stop DIY work and contact a certified mechanic immediately if any of the following apply:
- • You smell fuel, burning insulation, or see smoke.
- • Brakes feel soft, pull hard to one side, or make grinding noises.
- • The engine overheats, stalls repeatedly, or misfires under load.
- • You are missing required tools, torque specs, or safe lifting equipment.
- • You are not confident in the next step or safety outcome.